What's wrong, if the faucet is leaking. Repair instructions

30.10.2023

Mixes with an invisible element of the skin bath, which supplies hot and cold water. The temperature of the water that comes out of the tap is always regulated, and its pressure. In addition, the mixer has a re-mixer, which allows you to redirect the water from the tap to the shower. Like any mechanical device, there is no insurance against major breakdowns. Fortunately, its design is not too complicated, allowing you, in most cases, to solve problems on your own. In this article, we will look at the installation of a mixer for a bathtub with a shower, repair of the mixer in case of any breakdowns, and we will fix the causes of malfunctions.

Let's look at how you get out of the shower. This will help you understand the principle of operation in a structure-based manner. All the ingredients that can be used in the bathroom fall into 3 categories:

1. Sensors. The core element of such a device is a photocell, which gives a command to turn on the device in the robot and its operation. Self-repair of such devices is very difficult, so it is best to bring it up to the experts.

2. Ventilni. The mixer device for a bathtub with a valve type shower is very simple:

frame;
viliv;
valves. Designed for manual kneading;
Crane-tow. You can't regulate the water supply. Old models are equipped with gum pads, new ones have ceramic plates.

The photo shows the design of a valve changer with a proportional jumper

Porada: Ceramic crane axle boxes are much more durable than older models, and they are much easier to install, since the valve can be turned a maximum of 180 degrees.

3. Important. Currently, this type of mixer is gaining popularity. A typical model of importance is formed with the following elements:

frame;
viliv (gander);
ceramic or ceramic cartridge, which allows mixing of water. Ceramic cartridges do not require disassembly. If such a cartridge becomes unusable, repairing the bathtub and shower mixer requires replacing such a cartridge;
a rubber handle that regulates the water pressure and temperature. Attach to cartridge parts;
a nut that fixes the cartridge to the body;
The cover to the body, which covers the cartridge, is designed to give the product a more aesthetic appearance.

The main causes of mechanical failures

It is important to carefully consider the installation of a bathtub and shower mixer - its repair is not particularly difficult. It is important to know the cause of the subsequent breakdown:

The virobu is not happy with its virility. This is typical for the products of low-volume producers, who use unclear components and consumables in their work;
Vikoristannya vytratnyh materials old zrazka. For example, paronite or silicone gaskets serve much longer than humic compounds. In addition, the smell is less deformed and does not collapse due to drying out;
There is rude water in the pipes;
Increased hardness of water flows into the internal parts of the device, provoking the creation of the lining and cracking of the cracks.

The main breakdowns and their elimination

Let us look at the report on what kind of breakdowns can occur during the operation of the shower mixer, as well as how to maintain the mixer in the bathroom yourself. Malfunctions may be of the following nature:

The flow in the place of sticking of the goose with the body of the mixer

This is the most widespread failure, the fragments of the gander are gradually wrapped around the different sides, which leads to wear of the round gum pad. This gasket is located in the groove of the gooseneck; to replace it, the goosenecks must be removed.

Actions are concluded in the following sequence:

The fastening nut is unscrewed;
the gander is dragging;
Excess old gasket can be seen from the groove of the goose;
a new gasket is installed;
the gander is installed on the seat;
thread, on which a fixing nut is screwed, is wrapped with 2-3 balls of FUM stitch;
The nut securing the gooseneck is tightened.

Flow under the important thing that controls

This type of problem is typical for mixing and failure of the cartridge. It is necessary to change your mind, and replace the cartridge. However, there will also be a sign of cartridge failure:

important became important keruvati;
The temperature of the water supplied changes spontaneously;
there is no supply of either hot or cold water;
The tap does not close completely or opens all the way.

In this case, you need to replace the cartridge. Repairing a bathroom faucet with your own hands follows this order:

Important: There are protrusions on the cartridge body that may cause damage in the middle of the body. Eat them respectfully. If the stench cannot be eliminated, the smell will flow.

Leaking the valve of a double-valve mixer

The reason for the leakage of the double-valve mixer is wear or distortion of the pressure washer located on the crane box. The crane axle itself may also collapse. How is the flow of water in the bathtub - how is it beneficial and inexpensive? Only independently, replacing the faucet axle or the washer on it. There’s nothing fancy about him.

All robots shut down when the water supply is cut off:

Remove the plug from the valve that is leaking;
The screw is screwed in, which secures the valve to the mixer body;
behind the help of a lever or adjustable wrench, a crane-axlebox is screwed in;
the crane axle itself or the cradle ring on it are replaced;
a new or repaired crane-box is installed on the old place.

Flow of the faucet-shower pump

Between the faucet-shower mixer and the body there is another gasket that can get damaged. How can you help the mixer near the bathtub, what kind of pump “leaks”? Just took the peremikach itself:

The button (remixer) is removed, for which the rod is pressed into a fixed position with pliers;
the valve and the stem are drawn out;
a damaged oil seal is visible;
on yogo place a new oil seal is installed;
Peremikach is going to buy more.

Repair of the amplifier with re-mixing in proportion to the readings on the video.

Malfunction of the button or valve “faucet-shower”

If the button does not rotate after being pressed, then the spring is faulty. It is necessary to remove the jumper as described above, and then pull out the broken spring. On this place a new spring is installed.

If the pump is not used properly, and water flows out of the shower and tap at the same time, then the reason is cracked oil seal found on the peremikach rod. Necessary:

remove button (remix);
tighten the rod;
replace the oil seal;
take away the remixer.

Leakage in the area connecting to the shower hose

This problem is caused by faulty hose gaskets. If the bath mixer is leaking, do-it-yourself repairs involve replacing the gasket. To do this, just unscrew the hose nut by hand, and then remove the worn washer. On this place a new paronite washer is installed. Before tightening the nuts, it is important to cut and wind a couple of balls of FUM-stitch. here.

Leakage in the area connecting the shower head to the hose

How can you prevent the mixer in the bathtub from flowing water between the hose and the shower head? Quite simply. Under the nut located on the hose there is a round insulating gasket. The wire can be easily replaced without any additional tools.

Weak pressure of water

If the pressure of water through the mixer has weakened, and in the vessels it has lost itself, there is a trace of suspicion, first for everything, Checking the aerator filter, what is at the tip of the goose. Unscrew the slide by hand or with pliers, and then check the pressure. Since without the aerator the pressure had become stronger, the reason was due to its obstruction. You need to carefully rinse it under a stream of water, and then screw it in place.

Porada: Often it is not the aerator itself that becomes clogged, but the cleaning filter, which is located at the inlet before installation. If cleaning the aerator did not give anything, unscrew the filter and check the cleanliness of its mesh.

We learned how to repair a bathroom faucet with a shower with our own hands. With the use of clear, wasteful materials, such problems will be much less likely.

Do-it-yourself bathroom faucet repair video

There are a lot of reasons for the breakdown of mixers, related to unclear materials, incorrect installation and a variety of other factors.

To find out the cause of the breakdown, call the master or try to fix it yourself.

Reasons and procedure for eliminating leakage in the faucet

To repair an essential component with your own hands, it is necessary to determine the cause of its breakdown. There may be a lot of them, let’s look at the main ones:

mechanical damage, causing damage to the housing or the creation of cracks on the body;
closing the gap on the seats;
viroblennya on paved;
malfunction of the aerator due to rusting of the material;
gap on the aerator.

If the vinyl problem is due to a break in the case, the varto will speed up waterproof sealant or cold welding. Necessary parts are rubbed with gantry, and any damaged areas are carefully coated. However, such repairs cannot be repaired permanently, and you will soon have to completely replace the body.

If the water pressure is weak, it is necessary to remove the aerator and clean it and the brush screen. There may also be a blockage in the pipe through which the river goes.

If the faucet is leaking, otherwise it is not possible to determine the cause of the malfunction, it is necessary to thoroughly disassemble the entire mechanism and find the cause ground by checking the skin part:

The water supply is initially cut off, then the plug is pulled out with a twist.
Next, you need to unscrew the screw that holds the decorative cup in place.
Then the cartridge is pulled out - for which the nut is tightened with a wrench. All parts must be checked to see if they have any defects. Since such people have not been found, let’s move on.
Having opened the faucet, I was amazed at the gasket, springs, plug and humic duct. Damaged parts should be replaced with new ones. Those who have lost it are wiped with a rubber cloth to remove any debris and waste that has accumulated.

One of the most common problems is the loss of sediment particles under the valve stem and seat. In this case, you will have to change the entire cartridge.

Reasons for the reduction of leakage in a double-valve changer

The main reason for the breakdown of such faucets is their acidity. The seals on the valve axle box or the gasket may also be missing. These parts can be replaced.

Pokrokov's instructions for analyzing a double-valve mixer:

interrupted water supply,
clearing traffic jams,
tightening fastening screws,
remove the axle crane from the nut wrench.

Remove the plugs with a very thin twist, so as not to seal them.

The screws need to be twisted carefully, because the smell is often oxidized, and they are difficult to unscrew. You can vicoristuvati WD-40 or a drop of ottoic acid.

The crane axle box is screwed from the body with a nut wrench against the directional arrow. Stretch with fingers. For repairs, it is necessary to examine the seat in the body so that there are no cracks. Then the oil seal and gaskets are changed on the crane box. The assembly mechanism must be rubbed with silicone-based oil, after which everything must be put back together. Next you need to install the crane axle box and press it with the key. Be careful not to over-tighten the mechanism so as not to tear the splits in the body. If you are going to separate them, you will need to change all the mixing.

Repair of peremikach for shower

There are a number of types that change the soul, let’s look at some of them.

Zolotnikovy

The flow in such pumps comes from the handles that open and close the water supply.

The humic rings on the rotating rod were fitted or there are none,
the gasket on the axle box was worn out,
the axle box is twisted.

Having corrected or replaced parts, the switch must be collected and inspected. Don’t forget about the replacement of the switching mechanism.

To open this mechanism, you need to turn off the tap, remove the cap, unscrew the screw and pull the button out of the spring.

the spring has sagged and does not trim,
Valve rings were worn.

If the spring has collapsed, you can replace it with a new one or prepare it yourself. To do this, stretch it out and heat it until red, then immerse it in cold water. After cooling, it is necessary to reheat for even cooking. It is also possible to prepare the spring behind the dart using this same method.

If the valve rings become crunchy, replace them. After replacement, the entire mechanism is subject to staining with Vaseline or other ointment.

The main problem is that the plug fits poorly to the body and begins to leak. You can also do this:

filthy rubbing,
erosion to the mechanism,
presence of solid particles in the body.

In order to correct such a jumper, you need to unscrew the screw, remove the handle, unscrew the nut and remove the ring. After careful inspection, grease the parts with Vaseline and remove them in place.

How to fix a bathtub faucet that is leaking, dripping, running, leaking - options for repairing the faucet

How to repair a faucet in a bathroom? There are a lot of reasons for the breakdown of mixers, related to unclear materials, incorrect installation and a variety of other factors. Shchob

Repairing a bathroom faucet: causes of breakdown and methods of repair

The mixer is a device for regulating the temperature of the water that comes out of the tap.

The bathroom mixer also has the function of switching the flow of water from the tap to the shower. Unfortunately, the device often breaks down. But most often it is easy to insert self-tightening.

Main causes of malfunctions

Perhaps the most obvious reason for the breakdown of the mixer is the low viscosity of the vibrator itself. Today, the market is characterized by low-acid plumbing fixtures from China and Turkey, which have a low service life. When choosing a new mixer, the food supply may play against you. It’s better to spend it once, otherwise you’ll get a bright little thing that will serve you many times.

Another reason for some breakdowns may be the breakdown of unsustainable materials. For example, the use of humic gaskets when connected to hard water from the tap can lead to frequent breakdowns. If you have ceramic inserts, the parts will serve you much longer.

Incorrect installation can also often lead to various types of breakdowns and reduced service life of the device. When installing the mixer, it is important to take into account its design features.

For a report on the species, read our article about the choice of mixture. Here you will find a lot of great pleasures and recommendations.

The skins of these types of replacement parts are installed in their own way, and breakdowns in them can occur for various reasons.

Changing the volume of the jet from the tap

The most common problem associated with the work of mixing units is a change in the flow rate. The reason for such a malfunction, as a rule, is a clogged aerator - a nozzle that is attached to the end of the goose, through which water flows from the tap.

This problem in most episodes is easily resolved. You just need to tighten the aerator and clean it well, either under a strong jet of water, or blow it out with a jet. After that, all that needs to be done is to screw it into place. It's possible to earn money if you're a homemaker.

Leaking from under the clamping nut of the goose

Another common cause of mixer failure is wear of the gasket. Chantly, the skin reveals itself as it looks - it is a small circle of cushioning material with a hole in the middle. Previously, in old mixers, gum pads were used everywhere. It has now become possible to use more modern and reliable materials, such as paronite.

To eliminate leakage, we need a gasket of the same diameter, a spanner and a stitch made of fluoroplastic material, or a linen with a special paste.

Remove the metal ring and secure the pipe until smooth.
Remove the pipe and remove any excess worn gasket.
Dress up the new one.
Wrap the threaded pipes with stitch or linen and paste so that when installed, the parts are tightly pressed one to the other.
Secure the pipe with a metal ring.

Repair of a single-important mixer in case of detected leakage from the important part

Such a problem, as a rule, causes problems in the operation of the mixing cartridge. Let's figure it out first, what is a cartridge?

Cartridge– this is a collecting cylinder with three doors; Hot water comes into one hole, cold water comes into the other, and water flows out of the third.

Depending on the type of mechanism used for mixing hot and cold water, the cartridges are divided into ceramic and ceramic. In addition, the cartridge has a rotating rod on which it is important to attach. It is in this place that the process takes place.

When it is necessary to change the cartridge

Basic signs that it is time for you to change the mixing cartridge:

The water is not served either hot or cold;
The water temperature changes quite a lot, without changing the position.
The tap does not work at full strength or does not close sufficiently;
When there is a mix-up, it is important to report loudly;
Well, let’s face it, we have identified a larger problem – the obviousness of the progress of the disease is important.

Selecting a new cartridge

As we have already guessed, it is important to pay respect to the plumbing equipment. Give preference to cartridges from proven European companies And make sure you don’t get caught up in the tricks of the scammers that make copies of famous brands.

As a rule, if you do not install the entire water supply system in your house or apartment, you have no choice as to what type of cartridge you choose. On the right is that, regardless of the variety of models, that’s all There are two main types of cartridges: cartridge and ceramic.

The advantage of purchasing cartridge cartridges is the ability to disassemble the cartridge itself and repair it as needed.

The ceramic cartridge cannot be replaced, but must be replaced as a whole, so the ceramic plates are more durable and not susceptible to the negative impact of hard water. Since the water faucet was originally mounted with a socket on a viscous cartridge cartridge, you will no longer be able to install a ceramic one. And just like that.

Let's go back to the repair of the one-important unit if leakage is detected, it is important:

1. Unscrew the plug from the designated cold and hot water lines.

2. Beneath it you will find a screw. Carefully unscrew it with a hex wrench or a screw of the appropriate size so as not to damage the part. If you are unable to do this carefully, use a drill using a thin drill bit to speed it up.

3. Remove the important thing from the body of the mixer by pulling it uphill.

4. Remove the decorative element from kneading using your hands or pliers.

5. Unscrew the nut, which firmly presses the cartridge against the mixer body. To do this, use a spanner to quickly open it, and then carefully unscrew it with your hands.

6. Usi. Now you can pull out the old cartridge, safely take it to the store and buy a new one.

7. To install a new cartridge, complete all descriptions in order.

Do-it-yourself repair of a bathroom and shower faucet

One of the most common problems with the booth is the breakdown of the mixer. Today there are many types of changes, and to repair the skin they require their own approach.

Teche smіshuvach near the bath.

If there is a leak under the tap: what to do?

There is a leak under the tap in the bathroom. What is it timid? This information will be useful to everyone who wants to independently correct the problem. It doesn’t matter whether the faucet drips in the bathroom or kitchen, since all the nuances lie only in the design model. How to please the faucet? Water connections can be made throughout the apartment at the outlet, if there is only one riser per apartment. Both the kitchen and the bath room are located at different ends of the apartment, and there are obviously two risers, the water in which is blocked around the bathroom and the kitchen.

How to fix a leaking faucet

What should you do if the faucet is leaking in the closed position? The double-valve valve is leaking. This kind of faucet has been in use in apartments for more than a decade now. It’s just that wine has become more present. Even if I apply the same principle, problems will still arise. Double-valve mixing of the valves in such a way that one valve responds to the supply of cold water, and the other to hot water. Whose mixture has a worm gear. The most common problem with double-valve mixers is that when water drips from the tap, the tap starts leaking.

Which way is the gasket in the faucet going wrong? You can replace them yourself. The necessary virus can be purchased from any specialized store or on the market. Like the faucet, you know a lot of people. Aje is far from willing to go through such an insignificant breakdown of the Viklikati Master. Replacement sequence:

You need to turn off the hot and cold water first.
Unscrew the ram that secures it, the bolt.
The valve body must be unscrewed using the adjustable wrench against the directional arrow.
Replace the old gum gasket with a new one.
Then take any kind of tensioner, such as it, and, behind the year arrow, wind it under the thrust side onto the splitter.
Then tighten the housing. The valve is fixed with a screw so that it can be assembled in the reverse order.

It may happen that the gasket is new, the bathtub faucet works normally for a good hour, but after a dozen hours it appears that the faucet is leaking again.

For this reason, it is necessary to joke around the so-called faucet seat. After a long period of wear and tear, it may crack, become jagged, or fade. Then you should go through the problem area with a milling cutter and check it out. And the faucet is leaking.

In modern cranes, instead of a worm gear, a crane axle box is often used to accommodate ceramic discs. Whenever a faucet leaks, it is necessary to tighten the lock nut more than on other models.

If the leak does not stop, then replace the valve axle.

How can you repair a bathtub faucet?

Like a one-important joker. The rest of the time, two-important mixers step by step, and they are replaced by mixers with one important thing. The main plus is the handiness of the vikoristan. By turning left and right you regulate the water temperature, and up and down the pressure that is supplied. The main place in this design is occupied by cartridges: cylinder or disk. They need to be changed less often, because the faucet in such structures leaks less often than gum gaskets. The term of operation will be extended.

The ring and disk cartridges differ little from one another, but in the middle there are similarities. They are interchangeable, i.e. instead of a cartridge cartridge it is not possible to install a disk one. Therefore, when purchasing an important mixer, you need to know or contact the seller which cartridge is installed in this model in case of further troubleshooting.

How to repair a faucet, what is important and the culvert cartridge plays the role of filling? It’s not all that complicated, all you have to do is follow the instructions.

Shut off the hot and cold water, so that the valves that indicate the supply of water to the room are installed in the apartment. Then open the faucet in the bathroom and drain the water that was lost in the pipes after the water pressure rose.
It is necessary to unscrew the bolt that secures the mixing handle.
Then it’s more important to connect for the help of easy money. Know Yogo.
Now the threaded connection is twisted (removed) behind the year arrow.
When the faucet dome is removed, the plastic part is unscrewed.
If a blockage is detected in the laying of the gorge, it will need to be removed. If the relationship itself is weakening, you should replace it.
Then the ball (ball cartridge) is removed for detailed inspection. If it is determined that the part has gone wrong, or is defective, then the flow cartridge cartridge must be replaced.

It appears that there is a leak in the place where the water is attached, which mixes from the mixer to the shower. Every now and then, water drips from the tap, and drops appear in the area where the water mixes into the shower. It is important to install a gasket on the shower, as in a double-valve mixer, which can wear out over time. This explains why the water flows from the place to the shower. For this type, it is necessary to change the irritant, which may be paronite or humic. When purchasing a new gasket, you need to know that its diameter is ½ inch.

To change the gasket, it is important to change the connection from the shower to the shower, you need:

Turn on the water to the apartment, blocking the valves.
First of all, we need to understand the importance of what kind of shower is used.
Unscrew the bolt that secures it to the wall.
It's important to know.
Replace the gasket.
Where it is important to cut, it is necessary to wind some kind of loop, for example, a FUM-stitch.
An important thing is put on top of the split and reinforcement.

If the problem is that it is simply bad to fasten to the pipeline, and there is a leak under the tap for this very reason, you need to check the compatibility of all the parts that are connected, disassembled and reassembled. But such incidents are rarely dealt with.

How to thank a faucet that is leaking

Regardless of the sufficient reliability of the current faucets, situations often disappear when they begin to leak. The reasons for this may be a splinter, but most often everything is connected with the wear of waste materials of the wearers - gaskets. It’s not always easy to call the master to solve this problem, so you should think about how to fix the faucet in the bathroom with your own hands.

It is important to note that the modification of the changeovers today is based on a model, so there can be no universal instructions for troubleshooting. For skin types there are recommendations and procedures, which will be discussed below. It’s melodious, it’s not hard to press the fact that before the robots it is necessary to turn off the water supply valve - this is obvious.

Leakage from the shower head or the nuts of the shower hose

The breakdown is based on the failure of the gasket between the sprayer and the hose or the hose and the mixer. To repair such a faucet, you need a new gasket with rubber or paronite (diameter ¾ or ½ inch, seal type). You will also need pliers, a stitch and a small piece of fabric.

Using pliers, I will tighten the nut on the hose. However, it is not advisable to do this “in a clean look”; it is recommended to put a cloth under it so as not to stain the surface. Next you need to pull out the old gasket and replace it with a new one. The markings must be cleaned from the winding that was applied earlier. Following this is a vikoryst FUM page. Well, then let’s screw the nut to the watering can or mixer. All taps in the bathroom can be quickly turned on.

The valve is leaking. Double-ventilated zmishuvach

As a rule, such folding appears when the crane axle comes out of fret, the ring that strengthens the non-ceramic crane axle wears out. Ceramic crane axle box will not be able to tell you the cause of the breakdown.

Through the hole in the body of the axle crane, you can pump it to ensure that the ceramic discs are intact.

To maintain such a faucet, you need a new faucet axle or ring, a wrench and a screw.

To start, you need to remove the plug from the valve, and then unscrew the screw that fixes it, and remove the valve. Then screw off the main valve-axlebox, so that it is easier to identify the cause of the breakdown.

After this, it is necessary to replace the old faucet axle with a new one by replacing the ring that strengthens it. Then you can put on the valve, screw in the screw, which fixes it. Now the bathtub will retain its functions 100%.

Flow from the shower/jaw pump and back

The reason is that the gasket between the main part and the body is worn out. To solve the problem, you will need a hexagon, FUM stitch and gasket with rubber or paronite (diameter ½).

Therefore, we unscrew the screw that fixes it, since it is in the model, it is important to replace the worn gasket with a new one. Vikorist is installing a FUM line at the place where the pump is mounted. It is very strong and tightened with a screw (again, because it is not).

The pump is leaking from behind. One-important zmishuvach

Most often, this problem occurs when using an internal cartridge. To get it in, you will need a new similar cartridge, pliers and a similar screwdriver.

You need to remove the cap from the screw, unscrew the screw, remove the jumper and unscrew the cartridge. We replace it with a new one, and put everything back in order.

Leaking from under the nut (pressure) of the goose

Most likely, the cause of such a breakdown is wear of the gasket. To be on the safe side, you will need a similar new ¾ inch, FUM stitch, and Allen wrench.

You first need to unscrew the nut (I will press it) to secure the gander to the body of the mixer. Then you can pull out the old gasket and replace it with a new one. After this, you need to wind the FUM stitch on the thread.

There is a change in the bathroom - all about plumbing

If there is a leak under the tap: what to do? There is a leak under the tap in the bathroom. What is it timid? This information will be useful to everyone who wants to repair it themselves

It seems that in ancient times there was such a katuvana: a person was tied under water that dripped, allowing the drops to fall evenly and monotonously onto the dark area of disaster. After every hour, the water, drop by drop, brought the poor man to the point of becoming unsettled, and at this moment he was already ready for anything in advance, or else to pin down the hardened water.

Perhaps many of those who have heard for a long time how monotonous and unhydrated droplets fall from the mixer in the kitchen or near the bathroom, often know those unfortunates who happened to know the cake with water. Why is there a doctor installed near the apartment? This time it’s not just water that’s dripping, but pennies! Your finances are irrevocably flowing down the drain, although it doesn’t seem to be entirely friendly in terms of attitude. So let’s try to get to the bottom of this topic: “Why does water flow from the tap even if it’s closed?”

Why the faucet is leaking: we know the reasons

In truth, the reality is much broader. Beyond the grand scheme of things, there are not many reasons for this problem, the axis of which is the most widespread:

Unclear joke. Even though we often choose something for our home, because of the diminishing economy, we buy something cheaper and more conveniently, so that we can save pennies for something else. However, such a tactic can be a profit for every purchase, and the joy of the rewarded costs can be a disadvantage. Your savings could be the cause of a breakdown in the clan or, worse, an accident. It would be good if at this moment someone appears at home who can quickly neutralize the effects of such an accident. If not, then you may find out that the saying is about the stingy one who pays double - all about you. It’s not a good idea to save money on buying a product - make sure you’re buying a product from a manufacturer that you’ve proven yourself. Return respect to price! The already low price for the brand may be a sign that you may be tempted to sell the product.
Its installation is incorrect or unclear. Here you can also include a number of assumptions in the folding process. If you bought a bright and expensive mixture, you will need to pay special attention to its installation. Defects made during the installation process can ruin almost all the benefits of an expensive and safe mixer. If you trust the installation of the fakhivst, make sure that your professional details do not raise any doubts.
Wrong reason. It is important to remember that, no matter what, the faucet has its own operating characteristics. And that means the minds for which the generator guarantees the normal functioning of the equipment generated by it. In the end, as you reported above-world forces when installed or vicoristan, or pressed on the adjustment when turning, and also under the wrong cut, twisted the valve, pressed the nose to the above-world vice, then it’s not easy to find out that everything is And the manipulations will take place absolutely without a trace for anyone. Damage due to improper use is one of the main reasons.
Natural wear. On the right, as a result of cycles of turning on and mixing water, which are repeated many times, the elements of the mixer, especially the humic pads, begin to wear out. Who could benefit from preventive repairs and replacement of gaskets. However, rarely does anyone realize that the faucet can become dirty until it starts leaking. Therefore, most importantly, the problem is inevitable. It's too early to discover for yourself what nutrition is needed. However, you have the strength to do so. Let’s talk below about how you can earn money.

How to repair it yourself

We have already been told that we need to work hard to solve problems. To summarize, you can see 4 main points:

a reasonable approach to choosing a mixture of elements;
the installation is clear, it is important for the fahivets;
correct operation;
preventive repair robots;

All this guarantees the reliable functioning of the crane.

Well, first of all, before starting the repair, you need to determine the power supply, and they can be damaged:

water drips or leaks from the valve for turning on the hot water supply and cold water supply;
water drips or flows in a thin stream from the tap with the valve closed;
water flows onto the fastening stick until it is mixed;
water flows through the house, fixing water pipes to the mixing point;
water flows from the mixing bowl to the sink;
The mixture has obvious damage to the body, through which water oozes;

Once a leak has been identified, the first thing that needs to be done is to shut off the supply of water, both cold and hot. Obviously, the best option is to replace the old mixer with a new one. However, there is a total world that can be unique in a number of cases.

So, in case of any type of seizures that have been treated, the following steps should be taken:

The most likely reason for water dripping or seeping out from under the valve when the water is turned on and drying up is the loose contact of the faucet to the mixing or wear of the gum gaskets. To eliminate this problem, it is necessary to reconfigure the axle box so that it adheres tightly to the mixer, and also replace the gum gaskets. If you have a ceramic faucet installed, you need to tighten the silicone seal.
If the water drips or flows in a thin stream, then, after all, the edges of the axle tap are worn out, which prevents the water supply from being completely shut off. This breakdown occurs only in inexpensive, unambiguous mixtures. It is likely that the crane box will be replaced with a new one and/or the valve will be replaced. In extreme cases, if the first two attempts did not help, you need to replace the mixer. Make sure that the unevenness of the internal surface of the non-acid mixer can also cause rapid wear of the gaskets and the valve-axle when the valve is tightly screwed on.
Water seeping into the faucet mounting area before mixing can be the result of wear on the gaskets, or loosening as a result of abuse or rough use. The recommended solution is to replace the gaskets and tighten the valve tightly until it is smooth.
As water flows through the place of fastening the water pipes to the point of mixing, it will disappear for everything, making a long-standing defect in the installation known. Such a defect was the result of over-the-top tightening of the nuts, which over time led to damage to the gaskets. Another possible reason is unclear hoses that fail to install the tap. The most serious problem may involve replacing the gaskets with new ones, or replacing the hoses. When replacing gaskets, it is necessary to ensure that the nuts are not over-tightened in order to maintain the service life of the gaskets.
The reason for leakage at the fastening point to the sink may be due to the fact that the mixer is not tightly screwed on or because it has developed during operation. It also happens that the gasket, placed between the mixer and the sink, has become unusable. It is necessary to screw the mixer to the sink and replace the gaskets. You can also place the mixture on silicone. There is no problem with the flow.
Since there is obvious damage to the body, it is practically impossible to repair it. In this case, there are no alternative recipes for completely replacing the faucet.

Necessary tools and materials

During repairs, such tools and materials may be needed.

Spare crane axle;
A unique key and a set of keys;
Glue;
Set of twists;
Laying of different sizes;
Plumbing fum-stitch and/or gantry;
Electric drill and grinding attachment to it;
Silicone glands.

Most of the listed tools and materials can be found at any booth. In extreme cases, you can find them in any convenience store.

The most popular and clear valves (Chinese or Vietnamese) that work in household appliances go well.

The most widespread problem is a leaking faucet in the bathroom, which appears to be the case in good places. Householders in such a situation, as a rule, resort to calling a plumber, and in some cases, try to fix the leak with their own hands.

Having noticed that the faucet in the bathtub is dripping, we must first carefully study the design of the valve unit and become familiar with the principle of its operation.

I will build it in a special way

The design of shut-off valves is simple, which allows you to use the principle of their operation independently.

The stench consists of the following main parts:

solid lithium (non-detachable) body with a set of pipes for connecting;
loosening the middle of the locking device with the rod;
servicing water supply valves.

There is an elastic gasket in front of the skin tap, which helps prevent the water supply from being cut off. The inserted rod has a screw thread at the top, which comes into contact with the threads at the end. Due to the threaded joint when the rod is wrapped, it is necessary to lift and lower the shut-off valve.

Valve taps, which are installed at the warehouse of standard mixers, have a folding structure, into which an overflow mechanism is additionally introduced. Shower units have a special sub-guzzle hose and shower head.

Main reasons

If a leak is detected in a home faucet, first of all, pay attention to its operation in order to correctly diagnose the causes of the malfunction.

The stinks may look like this:

the valve seat was covered with scale or was completely out of order;
the seal has become useless;
The crane axle box was worn everywhere;
A large amount of rust has accumulated on the locking elements.

If a worn or rusty seat is detected, the entire assembly mechanism will have to be replaced with a new one. In times of minor wear, it is recommended to carefully clean it. The failure of the seal due to wear is the most common cause of faucet dripping.

To check for a seal malfunction, it is enough to check its effectiveness in different positions of the locking mechanism. If the valve does not leak when the valve is completely closed, and when the water supply is turned on, water begins to flow, which means that the pressure element is completely useless.

Increase your respect! You can make the tires yourself by cutting a suitable size gasket from a piece of old gum (from a tire like a bicycle wheel).

Leaks may be caused by minor problems that do not require serious attention. In some situations, you just need to tighten the nut, behind which the crane axle box is attached. However, most often there are serious defects that require a ground approach and major repairs.

Fixed leak

When dealing with the most common problem with a faucet that is dripping, it is important to remove it without haste, carefully following the instructions. If it is necessary to replace faulty elements, use acidic parts.

Get ready

If the faucet in the bathroom or kitchen begins to leak a little, it is first necessary to shut off the water supply to the outlet or the entire riser.

Important! When the water supply is closed, be very careful so as not to damage (break) the valve.

It is necessary to prepare a set of tools and spare parts necessary for repairing the crane so that it is in good order. Which set of culprits includes:

keys: universal spanner, standard nut;
set of twists (crossbar and simple slot);
humic preparations for sealing gaskets;
gorge stitch FUM;
soft fabric and a piece of foam rubber.

The remaining two positions may be needed for the removal of the brood or to be used as dry gaskets.

Repair of double-ventilated annex

First of all, please take care of the double-valve faucet in the bathroom, because the most common malfunction of the unit is wear of the gum or paronite gaskets. To replace them you will have to perform the following operations:

From the screws of both axleboxes, decorative plugs are removed, under which there are bolts that fix them on the body of the mixer;
after the fastening behind the gas key is unscrewed, the valves move and come out of the body;
In such a situation, gum gaskets that have been worn out can be easily removed and replaced with new ones (mostly paronite ones).

After replacing the locking elements, the structure is assembled in reverse order.

Increase your respect! Possible situations, if the reason is that the mixer is leaking in the bathroom, it is poorly secured with an axle box.

To resolve the problem, it is enough to lightly tighten the lock nut that secures the faucet. If, when disassembling the valve, it turns out that on the right it is not in the gasket, but in a broken axlebox, it will have to be completely replaced. It is important to know what the opposite part looks like.

Repair of peremikach for shower

The specificity of the mixer for the bathroom is the presence of a mixer to switch it to shower mode. It is here that leakages most often appear, which lead to immediate sleeplessness. It is noted that after starting to drip the mixer in the bathroom, you should check the type of pump installed in the new pump.

The specific features of the structure are divided into:

Remixers are of the spool type, which are prepared in a set with valves.
Mechanisms in the form of a cartridge are most often installed in domestic manufacturers.
Button switches.

The procedure for eliminating leakage in the shower valve will be seen on the button device. The most likely cause of a malfunction is damage to the gasket that separates it. To replace it, you need to cancel the following:

Carefully unscrew the button itself, for which you need a spanner;

Important! Remove the trace button carefully so as not to damage the decorative coating (as it protects the soft flannel).

There are ring-like gum gaskets on the rod that hangs, which need to be replaced with new viruses;
After replacement, the entire structure is assembled in the reverse order of disassembly.

Cartridge type remixers cannot be repaired and are most often replaced outright. To do this, just remove the plug, and then unscrew the nut to secure the mechanism. After installing a new cartridge, devices are collected in the reverse order.

Repair of a single-important equipment

Equally important mixtures are divided into culverts and devices made in the form of a cartridge. The most common problem with culvert mechanisms is the blockage of the filter type. To clean the trace, unscrew the nut in the joint area of the gooseneck and the body, and then remove the tubular mesh and clean it. After this, the entire structure goes back.

Devices of other types (cartridges) are discussed in the following sequence:

the plugs of blue and red barley are twisting around;
a special wrench is used to unscrew the bolt securing the adjusting rod;
The handle is removed from the device, after which you can gain access to the ceramic plate with the fastening nuts placed on it;
Then unscrew and pull out the disk cartridge.

For reliability, it is recommended to renew the intermittent element (regardless of its position).

Equally important cul-type mixers can be dismantled in exactly the same way as before. The importance lies in the removed part, which is placed directly under the faucet handle (the dome is what you call the dome). Behind it is a plastic ring and a metal bag that needs to be looked at carefully. If there are traces of defects on them, the mixing elements should be refurbished, and then the device should be removed in the reverse order.

Cracks on the body

The liquid at the bathtub or sink may leak through those where a significant crack has appeared in the body of the unit. These works may be caused by damaged structures of the material, which were caused by stress or fall of an important object. The body or handle may break due to wear and tear due to constant rubbing and alternation.

Confronted with the presence of a visible crack from which water is dripping, people should praise the decision to repair or completely replace the faucet element.

Increase your respect! Carrying out repairs is permissible as a matter of course, so replacing the part is not worth it at the moment. It is clear that the observed sunset is timely.

The most widely used methods for the partial renovation of a damaged part or part of the mixture are:

sealing with special sealant or glue;
Vikoristannya to the cold brewing method.

Vlasnik must be prepared to ensure that the faucet will look better after repair, and also come to terms with the fact that the material that is being repaired when renewed can dry out and become unusable.

Come in for prevention

Preventive visits allow you to prolong the service life of any type of fluids that are installed in everyday water mains (including water pipes from two major waterways). One mind of their effectiveness - remember to understand the design of the devices, including the main methods of disassembly.

Important! There are a lot of things to do with prevention, depending on the type of change and what class it belongs to.

To extend the service life of the cartridge filters, it is recommended to use special elements to filter and purify the water before it is drained into the dispensing mechanism. The smells are bathed directly in the mixing device and are periodically updated (the frequency of their replacement depends on the amount of water in the system, as well as the intensity of operation).

As a result, the cooler mixers are not so sensitive to the contamination of small food houses, which makes it possible to do without additional filtration. Most taps are subject to special preventive maintenance – replacement of spilled parts.

In order to ensure that the device is in good order, the fakhivtsy should replace the gaskets installed in the new gum at least once every two years. So the bathtub faucet is not dripping.

Doesn't work forever. When water starts dripping into the sink, you need to think about repairs. If the faucet is leaking, there are two options: ask a plumber or fix everything yourself. Read about how to maintain this plumbing element with your own hands.

Typical reasons

Causes of malfunctions in the kitchen. The stench lies in the minds of operation, design and equipment. Most often, a dripping faucet results from the wear of the seat, oil seal ring and gasket, resulting in the appearance of a cake or salt deposit.

First start before repairs, it is necessary to identify the cause of the leakage

You can do everything on your own, but rather than have to go to the shops during the repair process, prepare for the next step in advance. Everyone will feel better because you didn’t throw away the packaging. Make sure to include a repair kit, instructions, a diagram, and a description of the technology for repairing the machine. If nothing has been saved, then you can familiarize yourself with the process by watching the video and reading the relevant literature, and then add everything you need.

First of all, you should turn off the cold and hot water supply valve, prepare the tank to drain excess water, and dry it. Give the skin type its own repair algorithm.

Repair of a double-valve gearbox with a worm mechanism

The supply of hot and cold water in mixers of this type is controlled by two different valves. The weak link here is the gum gasket. The problem is simple: replacing the locking element, which is worn out, another one is installed. This process consists of several steps:

screw the body;
The valve is fixed.

Porada: if the repair kit is not preserved, the gasket can be removed from the cracked rubber, and especially from the tires, because the cordova threads it has increase wear.

If you don’t care about replacing the gasket, the faucet continues to drip, causing it to leak onto the seat. It is possible that cracks, roughness, and nicks have appeared on it. To prolong the service life of this element, you must clean it with a roller, placing it in the place where the worm gear is located and turning it in the drill. After checking the seat surface, we install the gasket and fold the valve and further check for leaks.

How to repair a double-valve mixer using a crane-axle box

If the faucet is leaking in a closed state or the valves are closed, you hear a cracking noise, which indicates that the drainage fluid has been worn out. The flow from under the valve is very easy to dry up: after removing the valve, pull out the valve axle and change the gasket. Then we tighten the thread with a fum-stitch and install the faucet in place.

Dismantling the decorative cover

If the faucet axle does not adhere tightly to the surface, this may cause a leak. To fix the problem, tighten the nut and tighten it.

Replacing the ceramic axle box in a double-valve mixer

If the faucet is dripping, we try to tighten the lock nut more tightly, if it doesn’t help, we have to change the axle box. If this thing on the right is completely new for you, then it’s better to know a video on this topic and marvel at how professional plumbers build a robot. Call the axle boxes to change completely, concluding the robot with the upcoming rank:

Porada: selecting the crane axle box, focus on disassembly. She's definitely going to get a lot of money out of size.

How to repair an important fixture in the bathroom or kitchen.

The one-important mixer is easier to operate, because Adjusting the temperature is done by turning the knob on the other side. To adjust the vice, it is important to either raise or lower it. The main element of the changeover is a cartridge - a ball or a disk. They are not interchangeable, so if there is a need for replacement, then you need accurate information about which of them is in the middle of the mix. Visually it is impossible to be significant. Let's take a look at the procedure for replacing a culvert valve:

Do-it-yourself repair of a faucet that is leaking requires a lot of effort, but this way the greatest problem is to avoid wasting an hour on the arrival of a specialist and a pittance on paying for his work.