Htc wildfire a3333 firmware 4.0. Flashing HTC Wildfire S smartphone via computer

There are two available ways to reflash HTC Wildfire S, the first of which is to flash the phone through a computer, and the second - through a memory card. You should decide which method will be the most convenient, and only after that you can start the process, strictly following the instructions.

Flashing HTC Wildfire S smartphone via computer

First you need to find, select and download from the Internet the version of the required firmware in RUU format. After that, you need to download and install the HTCDriver driver on your computer. If HTC Sync is already installed on your computer, there is a driver in the system and you do not need to reinstall it.

You need to turn on the debug mode on the phone (settings, applications, development, usb debugging), unload HTC Sync and connect the phone to the computer in charging mode. This is followed by the second stage of the task of how to reflash HTC Wildfire S.

On the computer, you need to run the exe file containing the selected firmware, agreeing with all the "popped up" warnings. The program will determine the model of this phone for the possibility of flashing and updating its software, after which it will show the current version and the new software version.

All information about the Android HTC Wildfire S will be displayed on your computer, and the phone's current software versions and the proposed new image are listed below. You need to start the flashing program by clicking on the "Next" button and wait about 10 minutes. Done! The new version of the software is installed on the device!

Flash via memory card

To flash the phone using the option described below, you need to find and download from the Internet a ready-made archive of one of the suitable versions intended for flashing the device from a memory card.

If you failed to find the archive with the desired version of the htc wildfire s flashing, then you should find the firmware version in RUU format, as in the first option. After that, you will need to run the exe file containing the selected firmware option.

The welcome window of the desired program will open on the monitor screen. Without closing this window, you need to start looking for the rom.zip file, which should be located in one of the temporary folders where the installed firmware version was unpacked.

After finding the desired file, you will need to rename it to PG76IMG.zip and then transfer a copy of this file to the root of the smartphone's memory card. After that, the window on the computer screen can be closed.

Next, you need to reload HTC Wildfire S into the bootloader. To do this, turn off the device, remove the battery, and then return it to its place. After that, while holding the "volume rocker" button, you need to press the power button.

As a result, the HBOOT shell will appear on the screen. The phone will automatically detect the update and check for it. When finishing the flashing process, you need to press VolUp, agreeing with the update, and wait for the process to complete. In this case, you should observe the status bar in the upper right corner of the display, and at the end of work, restart the phone again. It is advisable to delete the PG76IMG.zip file from its memory card after flashing the phone.

Can be flashed to modified firmware Cyangenmod.

The process of changing the firmware itself consists of two stages:

1. root the phone.

2. change of firmware.

I draw your attention to the fact that this firmware modification is intended only for certain phone models, so before proceeding, check the list of devices listed on the site. Otherwise, you risk losing your device.

There are several ways to charge your phone. I chose the one that is recommended in many sources, the so-called Unrevoked Metod.

The instruction is very simple. And the most remarkable thing is that the program exists in versions for windows, linux and macos operating systems.

Root Wildfire.

Instructions for getting a root phone:

1. Go to the site unrevoked.

2. Selecting HTC Wildfire from the list.

3. We download the program for the operating system that we are using.

4. If the operating system is Windows, you also need to install HBOOT driver.

5. We connect the phone, put USB into debugging mode (Settings-Applications-Development-USB debugging) and run the program as administrator.

6. The flashing of the phone begins, during which it is necessary to follow the messages displayed by the program. And in no case disconnect or touch the phone until the program displays the message “Done”.

While the program is running, the phone will be rebooted about 3 times.

As soon as the message “Done” appears in the program, we wait until the smartphone is fully loaded, check that the superuser item should appear in the list of applications.

At this stage, the first stage is completed. Wildfire is loaded and ready for firmware.

Firmware.

Immediately before the firmware itself, you must save all your data. Since during the firmware process, all information is erased.

1. Installing the program ROM Manager.

3. In the main menu of the program, select Download ROM.

4. We select the item CyanogenMod and select the last one in the list of versions. Optionally, install the Google Apps checkbox if we are going to use standard Google applications.

5. After the files are downloaded (the volume is quite large, it is recommended to use wifi), we will be asked Backup Existing ROM (whether to backup the current firmware) and Wipe Data and Cache (whether to clear data and cache). It is recommended to check both checkboxes and continue.

6. If a request from the SuperUser program appears, we allow Rom Manager to work on behalf of the system administrator, while setting the checkbox to remember the choice.

7. After that, the phone reboots into recovery mode, clears data and cache, and then installs CyanogenMod.

Upon completion of the firmware, the phone will reboot and a welcome message will appear on the screen asking you to click on the image of the robot. You must first change the system language using the corresponding button at the bottom of the screen.

Here is one moment on which I stumbled. Before entering your Google credentials, you need to set up wifi, since during the setup of your account you will be prompted to download several applications. If you do not do this and try to stop the download process, the account setup will not be completed, after which synchronization with Google servers will not work. However, you will no longer be able to run the Account Setup Wizard again. We'll have to reset all phone settings to factory settings and configure the device from the very beginning (as I had to do, having once again lost all the applications installed before).

Therefore, when asked whether to set up a Google account, we answer - set up later. The system will boot, configure wifi, and only then go to Settings-Accounts and Synchronization and add a google account there. A wizard will start, which will ask which applications you need to install, tick the boxes that you want to see on your phone.

We are finishing the setup and only after that it will be possible to fully use your phone.

Information taken from the site http://www.juev.ru.

The HTC A510e Wildfire S is a compact and time-tested smartphone. It is equipped with a 600 MHz processor from Qualcomm, 512MB of RAM and an internal SD card with a capacity of 512MB. Many will call this smartphone outdated, but the new firmware for HTC Wildfire S can give it a second youth. We will use the official stock update as the most stable and reliable option that we will install using a computer.

	Firmware:	https://yadi.sk/d/a3kmfKHSdJqtj
	Driver:	https://yadi.sk/d/h1iF9v05dJqth

Preparatory stage

Attention! This update is only suitable for devices with a locked bootloader! In the case of an unlocked bootloader, you must block it via HBOOT (to enter HBOOT, simultaneously hold down the power and volume up buttons while the smartphone is booting).

1. Download the firmware you are interested in. Please note that for this type of installation, your firmware must be in RUU format (exe-file).
2. Download and install drivers on your computer HTCDriver if you haven't done so before.

Firmware stage

1. Connect your smartphone to your computer in charging mode. Do not forget to turn off HTC Sync first and turn on debug mode (you will find it in the smartphone settings, in the menu Applications find the item Development of and select USB debugging).
2. Run the exe file containing the firmware on your computer. Ignore the warnings, agree with everything.
3. The program will automatically check your smartphone for the possibility of updating and display the current software version.
4. Click Next, wait 10-15 minutes for completion and disconnect your smartphone from your computer. Your phone is updated and ready to go!

Attention! If you have reverted to stock after custom flashing, be sure to do a full wipe of data and cache. If S-off, CWM Recovery and Root were installed on your phone, then after the update you will lose the last two applications.

Today we will deal with flashing HTC Wildfire S on Android of newer versions. Today we will install the firmware using Android Ice Cream Sandwich 4.0 as an example, but if you wish, you can upgrade to Jellybean (4.1). I hope this step-by-step instruction will not cause any difficulties on your part.

HTC Wildfire S firmware- step-by-step instruction

1. If you are not yet HTC, then I ask you to do this first to get Root rights.
2. Go to the XDA-developers forum and download the One Root 1.5 file for Windows. If you have a Mac - download the link below.

1. Next, unpack the archive, go to the folder and open the one click.bat file. A window will open in which we simply press any key and wait 30 seconds.
2. The next step is to flash our HTC Wildfire S and get the most custom firmware. We are moving on to the same xda-developers in a special theme with firmware.
3. As I said, we will be installing firmware 4.0 for a smartphone for example. So, I download the file: MIUI v4 - 2.4.2. Click here and scroll down to this post and click "Download": (Until recently, download links from XDA were workers - who could not download the firmware from the site - download here: Wildfire S MIUI firmware with Russian language support)

1. When you download the firmware, the next step is to upload it to Wildfire S via USB without unpacking (!).
2. (Important!) If you bet Cyanogenmod firmware any version you need: be sure to (!) download (http://www.teamandroid.com/gapps/) and drop again without unpacking (!) GApps (for each version of Android its own (select-download)) on the SD card, and before installing the firmware via Recovery, you must click install zip from sdcard -> choose zip from sdcard -> We are looking for downloaded GApps -> install. So that there was no later such that the firmware is installed, but after a reboot it takes a long time to load and does not load in the end, so it can take 24 hours and nothing is loaded. How it was for me! - I transmit thanks to Pavel Filippov for such a decision. It is also worth noting that the guy 2012 Wildfire S phone release, flashed successfully!
3. Then we take our phone - turn it off - hold down the volume buttons (decrease) and the power button until the bootloader menu appears "a.
4. Choose Recovery and wait a bit.
5. (Important!) In the new menu, go to the following items: backup and restore -> backup. A folder with a backup of your system will be created on the memory card. I think it will not hurt if the firmware installation is suddenly unsuccessful. It can also be downloaded to a PC and stored just in case. For a backup, you need about 500 MB of free space, so save in advance. System recovery goes through the selection of such items: backup and restore -> restore -> selection of the archive with the old system.
6. The backup is done, the next step is cleaning the cache. To do this, go to: wipe data / factory reset - wipe cache partition -> Go to Mounth and storage -> format / data - format / cache - format / system.
7. Go back, select Advanced -> wipe dalvik cache. Everything is now ready to install firmware on HTC wildfire S.
8. In the menu, select - install zip from sdcard -> choose zip from sdcard -> We are looking for the downloaded firmware -> install. At the very end, when the new system is installed, it will say "Install from sdcard complete".
9. Using the on / off button of the phone, go to the main Recovery menu, where we select the reboot system now item.
10. The first HTC boot will take a long time, up to 15 minutes, maybe more. That's all.

ATTENTION!

1.Before all the steps described below, save everything important in a conspicuous place on your computer, all information may disappear without a trace!

2. The success of manipulating the phone is facilitated by calmness, careful reading of instructions, making a copy of all information, including the official firmware.

3. Fully charge your phone, check for internet.

Re-flashing old by the standards of today's powerful devices allows you to do just fine without buying a new phone with a fresh OS, which slightly disappoints manufacturers. After all, they release new items altogether out of sports interest (although it is), and in pursuit of the attention of buyers, expressed in monetary terms. Therefore, most manufacturers in every possible way complicate the ability to change the firmware to an alternative one, they do not update the official one for a long time - if only they bought a new one instead of the “outdated” one. HTC is no exception, having released the successful HTC Wildfire smartphone ( among the people "Ogonyok"). Officially support stopped long ago, on system version 2.2, but enthusiasts are successfully porting the operating system to a fresher one. Traditionally, the process of changing the firmware of any phone (and Htc wildfire no exception) begins with replacing the bootloader. The native bootloader reacts to the archive with an alternative to almost obscene phrases, leaving no other choice. Sewing in another bootloader is not so easy - first we look at which version the official HBOOT has ... Squeeze the sound rocker down and the power button, hold - on the screen technical information will be displayed against the background of a picture with green robots. If after the word HBOOT you see numbers 0.80.002 - all is well, beautiful marquise, the path to experimentation is open. For owners of a smartphone with such a bootloader, the program will help you Unrevoked 3.32.

Download it here: http://downloads.unrevoked.com/recovery/3.32/reflash_package.exe.

In addition, to correctly identify the phone, we need to find the program HtcSync. It is located here: (on the right of the page). First, put HTC Sync, we are waiting for its download, make a copy of all the necessary data from the phone and immediately remove the program. Otherwise, it will interfere in the future. After the merciless removal, download the additional driver http://yadi.sk/d/kl3WxUCV18IjM... In the phone menu, select Settings -> Applications -> Development -> USB Debugging. Connect your phone to your computer, but first turn it off, hold down the sound button and turn it on. It will turn on in fastboot mode, which is what we need. Open the device manager and on Android 1.0, right-click the bear, select "install the driver from this computer / manually" and slip this archive. It is needed for the normal operation of the phone when connected. Now we run the program Unrevoked 3.32 from the administrator (right-click). The program will ask you for an action, agree to the installation. After a few minutes of waiting, it will shut down (the phone usually restarts in this case). Congratulations, the first step has been made successfully, you can go have a coffee and take a break while we help the owner of the phone with HBOOT for one.

For those who have larger numbers, starting with one - "Houston, we have problems." One means an updated version of the bootloader for our convenience - there will be a little more obligatory and tedious instructions.

The program will help us make a quiet revolution revolutionary. Download it from the developer's site - http://revolutionary.io/. There are links at the bottom of the page. After the download is complete, we do not close the site page, we still need it... In addition, to correctly identify the phone, we need to find the program HtcSync. It is located here: http://www.htc.com/ru/support/(on the right of the page). And the driver http://yadi.sk/d/vC5lX2RR18LEK don't forget it comes in handy. Put HTC Sync , then immediately delete. Run the driver installer downloaded above. Phone with USB debugging enabled (setting-application-development) connect to computer.

For the hack to work, temporarily disable the antivirus program, firewall. Overly vigilant security spies will close access to any changes, which will prevent you from moving on. It remains to run revolutionary. From the administrator, of course. A black terminal window will open:

In it, you can see the name of your phone, the version of the HBOOT bootloader and the serial number of the device (it is also under the cover). We carefully transfer all this data into the form on the site (I hope you haven't closed it yet?). Double-check each character carefully, the result depends on it!

Push Generate key and with Ctrl -C drag them to the window revolutionary. Press Enter. The work of the program is not fast, be patient, have a cup of tea. In the process evolutionary will ask you about installing CWM recovery, kindly agree. If after 25 minutes you still see the window without any action, something went wrong. It's not scary. We turn off the phone, restart both it and the computer and try again, starting with disabling the antivirus. Usually the second time everything goes without error. The success will be evidenced by the automatic closing of the program and restarting the phone.

Different versions of the loader are no longer a hindrance to us, we are starting to complete the epic. Download the latest alternative firmware from here: http://download.cyanogenmod.com/?device=buzz&type=stable(see by date the most recent

And additional Google services too: http://yadi.sk/d/Ms7AGDk318OLO

Connect the switched on phone to the computer and by pulling the top of the screen connect it like a USB flash drive. With an unwavering hand, throw two archives onto a memory card (I hope you have one?). You do not need to unpack the archives. Now a little bit is left - we reboot into the freshly installed CWM bootloader. To do this, hold down the volume down key and the power button on the phone off. In the menu that opens, select recovery with a quick click of the power button. The phone will enter the desired mode. In it, you can switch points by either an optical joystick (and select by clicking on its center), or by a sound rocker (select - the power button, by short pressing). Here, without missing anything from the list, we do the following manipulations:

1.Copy the official firmware to the memory card (if something goes wrong, everything can be returned to square one by restoring the old one. In the nandroid item, select backup. Wait for a copy to be created. In the future, do not move, do not change the name of the backup folder on the memory card ;

2. In the recovery menu, we are looking for wipe data / factory, wipe cache partition, and in the advanced item we need wipe dalvik cache. We choose only in that order;

3. In the menu item mounts and storage click on format system. Thus, we have completely removed the old system;

4. And the last choice is in the paragraph that is called installzipfromsdc choose choosezipfromsdc.

5. The first to choose cm-7.2.0-buzz.zip, we are waiting for the end of the process, then we go here and click the second CM7_Essentials_v5.zip.

It remains to reboot, look for the item - very slow, not less than 10 minutes. Then nothing unusual, it's time to set up - enter the login and password from the gmail mail, customize everything and everything in the phone to your liking.

You have succeeded, O young shaman! Congratulations!

Shamanism in the afterword

Overclocking the processor - no more than 710, although a few lucky ones are stable at 768 MHz. We look in the settings, setting Cyanogenmod-performance-CPU. Do not forget to check the box to save the new frequency value, but not immediately, but as soon as you see that there are no glitches of the device with the new speed. Then we lower it a little and try again. But remember - the higher the frequency, the higher the battery consumption.

It is advisable to calibrate (train) the battery after flashing. Use the phone with might and main, and when 1% of the charge remains, quickly reboot into recovery (you already know the method) and there is a wonderful option in advanced wipe battery stat. Select it using the tried and tested method and reboot the device from the menu. To drain the residual electricity from the phone, remove the battery for 15-20 seconds and put it back. Do not turn on the phone, but immediately plug the charging into it for 3 hours, at least. Then we enter the menu again and cunningly repeat wipe battery stat. Start up the machine, the problem is solved.

The third is also connected with the second shamanism. For some, an unpleasant event is observed - after putting the switched off device on charge, it cannot be turned on after a couple of hours. Do not be alarmed, this is fixable, and very rare. Pull the battery out for familiar 15 seconds, insert it again and the phone will immediately start normally. In the on state on charging, this does not occur at all. You can completely get rid of this by changing the recovery version in two minutes. It is not necessary to do this "just in case" in the absence of the described problem. How to do it? Download this version from another developer: http://yadi.sk/d/DqCN0LJi18QX I and without unpacking, we throw it onto the memory card. Boot into recovery again, select this archive in installzipfromsdc and we are waiting. Then reboot - and the problem will never return.