Homemade boat from PND pipes. Plastic Bottles and PVC Boat

Boat from PVC pipes with their own hands is a simple design. Its production will cost quite inexpensively, but the pleasure of the summer bathing season can get a lot. Make such a structure can be made of plastic materials on their own. This is not a difficult job.

PVC tube is the most convenient option for designing products with your own hands. These products are perfectly fastened with glue or soldering.

Even when the boat is damaged during use, you do not need to be upset. This repair will be not complicated on your own. With the help of the same glue, they simply impose a pay for a damaged place.

To the one, you need to add that the construction of such a boat is your own hands is very interesting work.

It was not bad at the beginning to make a decreased dimensional pattern, and glue such a construction from ordinary polyethylene packages. With this work, you can "feel" the material, and therefore, work with full-scale sizes will be much easier.

After working out patterns, they increase them proportionally. The masters advise to check the compatibility of the billets by performing the structure in natural sizes from polyethylene.

This, of course, will leave extra time, but it is worth it. If there are some errors in the calculations, it will be clear at the initial stage, and it is not necessary to spoil expensive materials.

Plastic pipe boat

A homemade boat from PVC pipes confidently takes a leading place among the crafts with their own hands from this material.

The most ordinary waterproof workpiece of the home master can turn into original floating.

Sequence of work:

• Frame. PVC blanks, a volume of at least 2.7 cm, cut into four parts. Two two meters and a half (for the upper part), and two with dimensions of 2.7 m (for the bottom). These pipes will serve as a carrier part of the design.
• Each end part of these billets should be cut at an angle of 45 degrees.
• Next prepare trimming a little smaller with such dimensions: 2 0.7 m, two to 0.6 m, two 0.4 m and two to 0.35m. These parts become supports for a boat frame.
• Support pipes are fixed to the frame. The ends of the billets must be fixed tight, otherwise everything will fall apart and go to the bottom. You can use adhesive tape or epoxy glue for attachment. For reliability, you can screw the holes in the tubes in the tubes and secure the design of the copper wire.
• A wooden board with holes is prepared, and fixed on the bottom of the support frame. For fasteners, plastic ties are used. The same fasteners are fixed and stool to this board.
• After that, the frame is covered with tarpaulin. It must be waterproof. It is laid on the diagonal, and all the protruding places are wrapped in the inner part. To the frame, the tarpaulin is fixed with plastic clamps. If there are rings on the tarpaulin, it can be attached to the frame after the holes are made in it. All folds need to stretch as much as possible. This will prevent unnecessary resistance during vehicle movements.

Keel

Kiel from the PVC boat pipe serves to endow the floodedness of increased resistance. Most often, the keel is on options using the suspension boat engine.

Set the keel so that its working part is in the nose area for swimming. From the Middle at the stern of Kiel goes to "no".

Another advantage of setting a keel is that it partially raises the nose of the design. And this in turn prevents splashes from entering with a big wave into the boat.

Manufacture of keel

Homemade keel on a boat from a plastic pipe is performed simply. All material that goes to work is distinguished by strength, small weight and small value. For the flat show, this keel will fit perfectly.

After detailed development and test check, you can begin practical work on the creation of a frame. You can consolidate the frame of the already proposed methods above, and you can use a soldering iron for plastic products to work.

It is not difficult to work with such tools. Even the person who has no experience in this sphere can cope with these works. .

Buy for one-time work to boil the frame, this tool is not recommended, justifying it with economic disadvantage.

It is better for fastening the frame of plastic pipes to use the device taken for rent. This service is offered shops that sell soldiers.

Frame from blanks, soldered by a soldering iron, will serve for a long time. At the same time, each joint of the frame will be highly durable. So do it yourself to make a very durable structure.

Buy such awning - the pleasure is not from cheapso many fishermen equip their "submarines" awnings that produce his armsand.

The simplest design is the awning that is attached to the frame, fixed on the racks. All this can be made of PVC pipes.

The work is done like this: tarpaulin or PVC fabric is fixed on the frame at the end. PVC pipes are lightweight material that will not be the total weight.

At the same time, they are quite durable, and the frame will not break with random engagement with branches or shrubs over the water.

The construction of the agent of PVC tubes done with their own hands can be very different, it all depends on the size and shape of the product, and from personal preferences.

A boat from PVC pipes will be unique if it is additionally decorated. Many of this moment pay special attention, for example, they are painted with acrylic paints, plywood and more are squeezed with painted sheets.

IN modern world Self-tech has many inexpensive materials from which you can make a boat with your own hands.

In this article, we will look at how to make a self-made boat from PVC pipes.

The easiest way to produce a boat from PVC pipes is to collect a frame of a self-made swimming agent using a tape and pull the polyethylene film from above.

This method of assembling a boat with their own hands is very simple and does not require any tools, it does not except the knife or saws for cutting plastic pipes in size.

Look at the video manufacture of a homemade boat from plastic pipes and films.

As you can see - the difficulties are practically absent!

But the test of this boat is afloat.

It must be said that not too adequate swimming qualities of this homemade boat lie completely on the hands of the collectors.

In fact, all homemade boats for such technology have in their prototype kayak lawyer Egorova.

Only he came to the manufacture seriously and his result was much better. It all depends on you only!

A homemade boat can not be wrapped with a film, but to use banner tissue. This will avoid leakage, and the strength characteristics with a crawling boat with a banner cloth will grow an order of magnitude.

Drawings of PVC Pipe Boats

The easiest way to get a drawing of a homemade boat from PVC pipes is to use a 3D editor. So, for example, for auto channel there are special libraries with plastic pipes, fittings and fasteners. Using it you can get the drawing of almost any self-made boat from PVC pipes.

The second variety of homemade PVC pipe boats is the manufacture using large diameter pipes.

Here are video testing such a homemade boat

Here it is already approaching the manufacture of big labor costs.

On the video below, the process of manufacturing such a boat in the garage conditions is shown.

To connect PVC pipes, you will have to purchase a special extruder or make it yourself.

However, make such a boat - it is only half the time. The second part of your time will go to the equipping of homemade PVC boats from the pipe fittings, as well as the installation of the transom and sidewers.

It is worth talking about price.

The cost of making a self-made boat from PVC pipes of large diameter with their own hands depends greatly on sizes. So, for example, a homemade boat a length of 2.5 meters at cost will rise in 5 - 7 thousand rubles. And the boat is a long 5 meters away from 8 to 9 thousand rubles, while in the store, the cost of boats of this size with a hard bottom begins from 38 thousand for 2.5 meter and from 50 thousand for 5 meters.

As you can see, the economy of the manufacture of a self-made boat from PVC pipes is very acquitted.

Soon summer, which means the swimming season. It would be nice to make a simple boat using plastic pipes. To create such a boat, approximately one month will be required, and the school pool will be suitable for its tests.

Step 1. Required materials

For boat:
Plastic pipes (PVC) - 122.5 cm
Plastic pipes (PVC) - 401.3 cm
Tree board - 1 × 0.5 m
Plastic clamps - 50 pcs.
Adhesive tape - 2 rolls
Foam block - 2 pcs.
Porolon - 30 × 30 cm - 2 pcs.
Nylon thread
Chair - 1 pc.

For support (optional)
Tree rails - 122 cm × 5 cm
Bottles (for water) - 4 pcs.
Super glue
Screws (for drywall) - 8 pcs.

For Visel
Aluminum tube - 225 cm
Acrylic sheet - 40 × 40 cm
Bolts, nuts, washers - any sizes, 4 pcs.

Manufacturing instructions:

Step 2. Boat frame

For the frame of the boat, it is necessary to cut plastic pipes into 4 parts: (for the upper part) 2 × 2.5 m, (for the bottom) 2 × 2.7 m. These parts are the carrier frame of the boat. Each pipe must be cut at an angle of 45 degrees.

For the reference part of the frame, it is necessary to cut 1.3 cm of plastic pipe for 2 × 70 cm, 2 × 60 cm, 4 × 35 cm, 2 × 40 cm. The photo shows how to cut the support pipes on each side to secure them.

For the manufacture of the frame, it is necessary to connect the ends of two trimmed pipes of 2.5 m with adhesive tape. They are fasten tightly "face to face" so that the boat will not break and drowned. You can also use epoxy adhesive for better fastening of the frame parts.

It is necessary to drill holes in the upper and lower part of the frame, and then connect them with copper wire.

You need to add support pipes frame.

Step 3. Fastening chair and foam rubber

Wooden board must be fixed to the bottom of the support frame using plastic ties. To do this, it is necessary to drill several holes in it. Also, several holes need to drill through the chair and boards, and fix the chair on the frame, with the help of screeds.

Step 4. Saving frame

In order to cover with a plastic skeleton, it is important to pre-make sure that it does not pass water. To begin, the kayak turn over, and then be covered with a barrane diagonally, all the extra, outstanding parts are laid inside the boat.

The tarpaulin is fixed with ribbons on both sides and fasten with plastic clamps to the frame. In case the lining with rings, they can also be fixed to the frame, for this, the holes should be done on the frame.

To avoid excessive resistance while swimming, it is important to most easily straighten the folding folds.

The foam is added to the bottom after fixing the plating, but carefully, to not spoil it.

Step 5. Making Pun
For the manufacture of the oars, 2 meters of aluminum pipe are needed, in which two holes are drilled from two holes, at a distance of 10 cm from each other. Cut 2 pieces acrylic with dimensions of 20 × 40 cm and spin the edges.

Acrylic is fixed using nuts, bolts and washers, pre-drumped the corresponding holes on the pipe and plate. Need carefully and gently tighten the nuts on the plate, because Acrylic can crack.

Step 6. Fastening of remote bugs
If the boat is unstable rests on the water, you can attach 2 bottles on remote supports on each side. It can be limited to one side, also effectively.

PVC is a modern material with a lot of positive qualities. It is rather inexpensive, lightweight, durable, durable, resistant to different climatic conditions and environments. In addition, plastic pipes are easily and quickly connected, providing absolute tightness of the joints.

Due to this, the use of plastic pipes has been widely popular not only when installing water pipes and sewage systems. Of these, "folk craftsmen" do with their own hands make a lot of useful "pieces", ranging from racks and drinkers and ending with sleds and flooders.

In this article we will tell you how quickly and inexpensively make a catamaran from plastic (with your own hands.

Building articles

Why catamaran?

There are mass options, as well as their destinations. For those who live near the reservoirs, especially for those who have to overcome the water barrier is a vital necessity, the catamaran will fit perfectly. Such an option of the vessel has a lot of advantages Before kayaks, boats or yachts.

• for the manufacture of catamarans from plastic pipes required minimal amount material. In addition, remnants from the recent installation of sewerage or water supply can be used;
• catamaran has a small weight, so does not cause problems in transportation issues;
• due to the features of the design - two cylinders connected by deck, such a floating has high seaworthy qualities, strength, reliability and sufficient speed;
• the ability to accommodate the required number of seats;
• on the catamaran you can install the engine of any type.

What is the catamaran?

Catamaran has a large number of Design features, in comparison with other plaques.

That's why it is necessary to know its components in detail, Before proceeding to drawings and installation work.

1. The first, and the most important, part of the catamaran - floats. These are two chamber structures located on the sides of the Floor. Their immediate task is to hold the ship afloat. Cylinders can be made of different materials that limit the external perimeter of the float. To do this, use the film from which inflatable cylinders, foam or pVC pipes.
2. Connecting frame. It can be made of any materials, ranging from all the same plastic pipes and ending with wood or metal. The easier the frame of the catamaran, the smaller the size can have floats.
3. Deck. This part is created to accommodate passengers, baggage and other things that will be transported by water.
4. Steering wheel. The function of the steering wheel in any flooding performs a submarine blade, which is directly installed for the movement, parallel to the movement, for rotation is rejected into one direction or another using a rotary handle derived on the deck.
5. Pedals, motor, motor or any other device, leading catamaran in motion.

Calculation of the sizes of the vessel

The diameter of floats, as well as the width and length of the vessel depend, first of all from where and how it will be operated. The more the crew is supposed and the more cargoes will be transported, the greater the size of the board and the diameter of the float should be.

Increase the vessel's carrying capacity by increasing the cross section of cylinders or their length. The decisive factor in this situation is the volume of air inside the cylinders.

Optimal parameters for calculating floats, Based on the crew and loading capacity:

• single catamaran must have a length of 2-3 meters with a transverse section of a cylinder 0.3-0.4 meter;
• for the manufacture of a double vessel use cylinders with a length of 3.5-4 meters with a diameter of 0.45-0.5 meters;
• three and four-seater floodeds have a length of up to 6 meters when the float diameter is 0.5-0.6 meters.

Catamaran is not recommended for more than 6 meters long, as he will lose almost completely his maneuverability. Although if you are going to swim mostly in a straight line, there is no restrictions on the size of such a "boat".

The larger the size of the vessel, the greater its permeability and stability, but less maneuverability. This applies to both its length and widths.

The width of the catamaran, first of all, is determined by its purpose and the way to act. If you make a catamaran for alloy along the river on the messengers on the principle of kayak, its width should not exceed 1.2 meters. IN otherwise, Water capture in the oars becomes impossible. If we plan to land rowes to cylinders, the width of the vessel can be increased to 2 meters.

If the catamaran is fishing or pleasant and it is planned to equip a sail, a motor or pedal blades, its width can be increased yet.

The width of the catamaran should be at least one and a half times less than its length.

Production procedure

To make a catamaran with your own hands, you need to decide on its purpose and, based on From this, calculate dimensions. We will look at two vessel options: the simplest single and tourist raft based on catamaran.

Single catamaran.

The manufacture of the simplest single catamaran is starting from the manufacture of floats. We take two pipes of the same diameter and length (based on the calculations given above, we will need plastic pipes for the outer sewage with a diameter of 0.4 meters and a long 2 meter). On the one side of both pipes are fastened. This will be the back of the catamaran.

The front part, for greater passability and maneuverability, you need to lift. To do this, we use two plastic knees with a bend of 120 degrees. Confirm them on the second end of the pipes and also close the plugs.

When assembling cylinders, pay special attention to the tightness of the joints. The slightest depressurization can lead to the cooler of the vessel on the water.

Floats are ready. You can start assembling.

To connect floats to one "whole" catamaran, you can use anything. Plastic pipes of small diameter are suitable, Wooden bars, metal corners and so on.

1. From the material you choose, we make 1.2 meters wide width.
2. We establish cylinders strictly parallel to each other so that the bends look up and in one direction.
3. Fix the transverse strips over the cylinders. For fastening, both clamps and self-tapping screws can be used, which can be screwed to the floors for greater strength.
4. We set any comfortable sitting on the transverse beams, take in the hands of the oars and rowing, where we want.

Single catamaran from plastic pipes with their own hands (video)

Tourist raft

The basic principles of the manufacture of these two plaels with their own hands do not have special differences. The only difference is that The walking raft will be calculated clearly not per person. And even better, if there is a cargo in the form of provisions, an umbrella from the sun, clothes of dishes and other things.

1. We make floats specified in the method above. But take a pipe with a diameter of 500-600 mm and 6 meters long. This will make it possible to make a steady and passable vessel on which you can reiterate without experiencing the crew.
2. We make a solid frame size 6 * 2 meters. Since the frame not only must hold the cylinders in proper positionBut also serve as a platform for deck, it is better to make it from metal corners.
3. On the pipes from which the floats are made, the clamps are dragged to which, in turn, the frame is attached using bolts.
4. On the frame they make flooring from the boards.

This design allows you to install any driving device on the catamaran, ranging from the blades driven by pedals, and ending with gasoline engines.

In addition, this platform allows you to fully sunbathe in the sun, heals the fish, in general, fun and fruitfully relax in a narrow circle of the best friends.