With the help of a modern tool - - it can be easily carried out direct and curly rods in a variety of leafy materials. Tree, plastic, metal - everything is possible. Naturally, within the technical characteristics of the tool.

Using the electroller, you can neatly cut the corners of the table or perform the curly cutting of the steel sheet.

Based on the density of the cutting materials and the technical capabilities of the electrolovikov, you can select some features of their use.

Features of using electroballs

• Availability pendulum mechanism Electrolovikov helps to avoid excessive effort during cutting; Increases the speed of the cut. The involvement of this mechanism is justified only in cases when there is no need for clean or accurate cut. Otherwise, the pendulum should be or disconnected, or put on the minimum position. The most optimal use of the pendulum mechanism will be cut by soft wood, as well as foam, plastic, plywood, chipboard.
• For sawing steel sheets or other solid materials, it is reasonable to use the electrolovka with a greater power. It is also necessary to pay attention to the method of fastening the peel - the cutting tool organ. Hard fastening contributes to a more confident cuticle.
• To perform work in everyday life, electric buses are used with a power of 280 to 550 W with an efficient power of the device within 130-340 W. Even in the household power tools should pay attention to the presence of electronic adjustment frequency moves With different loads and materials. If the adjustment is, even at low frequencies, the tool operates in full power, which has a positive effect on the speed and quality of work.
• When working with plastic, the use of high speeds of the saw can lead to the fact that the edges of the material being processed will be melted, worsened appearance and quality of work.

At the same time, the use of high speeds with cutting steel sheets is the most acceptable option. In this case, heating, steel becomes softer and militant.

The figure cutting of solid wood and other dense materials is also better performed at high speed.

In any case, when choosing a speed of the cutting fabric, you need to consider the need to obtain a clean cut. If you need special accuracy and purity, then the speed of the peeling rate is reduced.

In order to work with an electrolybike effectively, it is important not to forget that each tool exists to fulfill the work characteristic only to it. In other words, clog nails with pliers are also possible. But will it be effective? As for the power tool, the use of it is not prescribed almost always leads to deposits. Therefore, if it is necessary to make a long straight propyl, a good hacksaw, in the absence of a manual circular, will be the best option than the electrolovka.

10 tricks for efficient use of electric bias

1. Let the tool, and not you, performs your work. Your task is to just lead it in the right direction. Do not press on the jigsaw. This advice will not only retain your strength, but also help to avoid unpleasant moments in the form of a poor-quality cut, a broken militant, or what is more serious.
2. Use the canvas with sufficient width to implement long straight cuts. The large plane of the canvas will allow without overly effort to keep the desired angle of cut. Have a few crafts for different occasions of life. For fixing cuts, use the corresponding web, such as Makita B10.
3. If necessary, cut a thin metal sheet (less than 1 mm) Use a sheet of plywood as a substrate. When working, avoid vibration by selecting the optimal speed mode.
4. When used in the work of low speeds, let's easily give the "rest" electrolybiz. This is due to the fact that in small turns blowing the electric motor small. Therefore, with long-term operation, overheating may occur.
5. Perform all prescriptions for the manufacturer to maintain the power tool. Conduct the necessary lubricant, cleaning; Use and store tools in proper conditions. Thanks to this, he will serve you for a long time.
6. When working, fasten the material using clamps. Some electroloviki can be quite successfully used by one hand; You can also work with a partner. Despite this, to perform high-quality work, the fixation of the material plays a paramount role.
7. Turn on the pendulum mechanism when cutting wood along the fibers. It helps to cut into direct. The canvas will not be ahead of the fibers of the material.
8. Use personal protective equipment. Although many models of electrolovki are equipped with a nozzle to connect a vacuum cleaner or a dust collector, this tool is still quite strongly dust. Dust, accidentally falling into the eyes, will not improve the quality of work.
9. Draw up the line, and not on it. The benefit is not only that it is so easier to qualitatively cut the material. When you mark you, you do not have to make tolerances on the width of the propil.
10. When processing delicate materials, put down the front side. At the same time, if the material is fat enough, and you are not sure that you can withstand the saw perpendicular to the material, then turn the front side up and, if possible, wear a special antifriction overlay on the sole.

Knowledge of features and small tricks of using electroballs will help you perform work quickly and efficiently!

Lobzik is a universal device intended for figure sawing of various materials. The device easily copes with wooden, plastic, tiled and even metal products. Understand how to use the jigsaw, you can study the operational and technical features of the tool.

Depending on the field of application, the jigsaw is divided into two main class - household and professional. Regardless of the type, the design of the tool is equipped with a saw fixed in a special frame.

For home use, a small size of fixtures for cutting materials are used. Such tubes can be with manual or electrical control. Each type of tool has its own technical and design characteristics.

Manual

Such a tool refers to the simplest type. It consists of a frame, saw blades with clips and handles. It is used by a manual jigsik mainly for minor work requiring a certain loose accuracy.

The bottom tool allows you to perform art cutting material. But its use requires patience and skill. The feeding rate of the manual fixture is low, so it is impossible to apply it for large volumes.

Electric

Lobzik, working from electrical networkis considered the most convenient tool. It allows you to quickly and qualitatively split any material. The depth of propyl mainly depends on the power of the device. In modern devices, such an indicator can be from 200 to 900 watts.

For household use, electric bits with low power are suitable. They have a relatively small cost and perfectly cope with sawing wood products to a depth of 50 millimeters, and metallic - 23 millimeters. More complex work requires the use of the tool with the highest technical parameters.

Nuances of electric jigsaw devices

Modern manufacturers produce various models of electrolls. The design of any kind of tool consists of such main elements:

1. Cutting canvas. All electrical jigsaw are equipped with a special saw, with which the material is cut. The processing process is performed due to the rapid reciprocating movements of the cutting element. At the same time, depending on the model, the device performs from 43 to 58 revolutions per second.
2. Support sole. Such a piece of construction provides cutting accuracy. In most produced electrical jigsaws, the guide plane rotates the floor in any convenient angle to 45 degrees. Some models have a fixed slope value.
3. Engine. The electrical tool is necessarily equipped with a special driving system, which drives the rotating mechanism. The greater the power of the device, the higher its operational capabilities.
4. Holder. Such an element allows you to hold the tool in proper position During the entire workflow.

Some models of electric jigsaws have additional equipment. It can be a backlight or device for automatic chip removal. Many tools have cut regulators that make it possible to independently set the revolutions of the cutting element for each individual type of material being processed.

General rules and features of operation

The quality of drinking products both manual and electric jigsaw depends on its proper use. Each type of instrument has its own operational features to be taken into account during the work.

Manual Lobzik

There are several points that should be considered when sawing the material with a simple jigsaw:

1. All movements tool must be vertical. The jigscription should be kept straight, otherwise the saw quickly deterrently, and the cutting process itself will slightly delay. The movements are performed only in two directions - up and down.
2. Do not strongly press the tool. Excessive efforts can significantly reduce the quality of drinking. Lobzik is needed with a neat and light pressure, and when the lift is recommended absolutely free.
3. When cutting the picture, only the canvas is rotated. Lobzik should remain in the original position. At the same time, one hand need to hold the tool, and the second to provide the turns of the material according to the intended sketch.

Electric Control Lobsik

The use of an electroll bias requires compliance with its rules that will help qualitatively perform cutting material:

1. To bring the tool to use you to connect it to the network and press the start button.
2. During cutting, always press the support sole to the material should always be pressed. This will allow the cutting of the web exactly along the intended line.
3. The reference bar should always be in a perpendicular position relative to the material being processed. The improper arrangement of the guide sole can lead to a damage of the product and the most cutting element.
4. With a figure, the strollers should be made at least for a minimum of effort. Any excessive pressing of the tool can spoil the workpiece.
5. If it is necessary to perform sections at an angle, it is necessary to pre-adjust the support sole.
6. When running electric jigsaw, there should be small breaks for ten minutes every half hour. Such an action will help protect the device from overheating and much will extend its operational period.

When the electric tool is first used, small speeds should be set. This will allow you to feel like a logby and get used to it.

Technology work with electric jigscom

With the help of an electrolybiz, you can cut a different material without much effort. But still the quality of work requires a special approach to each type of canvas.

Selection and preparation of material canvas

Electrolzik can cut the canvas of different density. Products from wood, plastic or tile can be material. Also, with the help of an electrical tool, you can cut the metal.

Billets for sawing should have a homogeneous structure. If wood canvases are used, then the presence of bitch or metal elements should be excluded, such as brackets, nails or screws. Billets made of wood are used for cutting only in a leaking. To cut the drawing, it is recommended to select the material with a flat surface.

Selected for processing canvas is fixed in a horizontal position. On its surface with a pencil, lines are applied for cutting.

Wood saws

For working with wood materials in the instrument, special pinks with rather large teeth are installed - from 2 to 6 millimeters. Than complicated form The cut, the less should be their size.

Direct cutting of a wooden canvase can be performed on the highest rev.. With more accurate drinking products, the speed of rotation of the cutting element can be reduced.

To increase the velocity of the material processing, it is recommended to include a pendulum move. It is used if the quality of cutting does not matter much.

Saw should be smoothly without much effort. During operation, the tool should be smoothly pressed against the surface of the workpiece.

Metal processing

The cutting cloth in this case should have small teeth, the distance between which does not exceed 1 -2 millimeters. In the process of sawing a metal cloth, pendulum turns completely disable. The processing of the material is performed at the lowest speed.

Lobzik needs to move very slowly, eliminating any pressure on the tool. Before processing, the material is fixed so that the plus line is as close as possible to the support.

Saw plastic

The cutting canvas for plastic blanks does not differ from the saw for metal. In the pumping process, the minimum position of the pendulum stroke is set. For more smooth cuts, it is completely disconnected.

Plastic processing is performed on low revolutions. The tool is tightly pressed to the canvas and moves smoothly along its surface.

Split tile

Such products require a special milk, in which abrasive material is applied on the site of the teeth. In this case, the pendulum is not used. The entire workflow is performed on the maximum speed.

Cut tile tile Electric jigsaw applies only if necessary for small sections. This is due to the fact that the saws quickly deteriorate and require frequent replacement.

Features of drinking

Electric jigsaw easily copes with rectilinear sawing. Also, using the tool, you can perform various cuts at an angle and cut into the billet oval or circle. Performing each type of cut has its own characteristics.

Round and Oval Elements

The contour of the figure is applied to the prepared canvas. After that, with the help of a drill in the workpiece, a hole is done in which the logs is installed in the cutting element.

The process of cutting begins and ends in the work done. If you drift a few holes, then the circle or oval can be chopped in parts.

Straightforward

With this type of cut, the electric jigger copes the easiest. On the web there is a markup, on which the instrument is smoothly carried out.

For direct sawing material, you can set the highest speed. Before starting work, the workpiece is recommended to consolidate.

At an angle

Such a crucible material is performed at a preliminary setting of the sole under the necessary degree of slope. After fixing the desired angle, the same actions are performed as for rectilinear cutting.

Nuances of rectilinear drinking

For cutting material in a straight line, a guide bus or parallel stop is often used. Such additional devices are much facilitated by the workflow and allow you to improve the quality of the cut.

Shine guide

Such an auxiliary device is a metal ruler in which the groove is located for the installation of a special sole and an electrolovka.

Before starting work, the material marking is performed. Thereafter

The material marking is initially performed. After that, the bus is fixed on the line. The electrical tool is easily moving to the device, carrying out accurate and even cuts.

Parallel emphasis

All models of electric jigsaws in the support sole have a special hole for installing a special bar of parallel stop. The device can be purchased in a specialized store, but often it is included in the tool.

Parallel emphasis provides an even cutting of various billets. But the use of such a device requires some conditions:

• when the tool is moved along the canvas, it is necessary to press the sole sufficiently tight;
• the surface at which the device will be moved is absolutely even.

The design of the parallel stop must be sufficiently strong and strong. Installing fixtures to devices that can be dismissed when cutting aside.

The most frequent breakdowns and methods for their prevention

Quality electroballs have a sufficiently long use. But even the very better model May suddenly fail. Most often, breakdowns of such parts of the instrument arise:

1. Start button. Basically, such an element of the design ceases to work when the metal dust is inserted into the housing. To troubleshoot the fault you need to perform simple cleaning with a special vacuum cleaner. With prolonged use of electric jigsaw, the button fails during the wear of the mechanism.
2. Mechanical connections. Most often spoiled stock. For such an element, mechanical loads are most affected. The village often fails to lock the fixture that is connected to the rod. Everything is marked inwards inside the dust housing during cutting of various materials. But if the tool has a high-quality case, then there are practically no such problems.
3. Engine. The stop of the electric driving mechanism can occur when the stator or rotor is bravely. Sometimes the problem occurs due to wear on the shaft of notches. In order for the electrical device to work for a long time, it should always take into account its power before setting certain tasks.

Incorrect use of the tool leads to high loads, and subsequently, the failure of the mechanism. With prolonged drinking, it should always be given periodically jigsaw a little cool.

Safety technique

Lobzik refers to enough easy tools. But still the presence of a sufficiently acute cutting element requires compliance with some security rules:

1. Cuts of any materials should be carried out on an even stable surface with a preliminary consolidation of the web. It is completely eliminated by cutting parts on weight.
2. Cut the blanks should be at a distance from the eye of at least 40 centimeters. To protect it is recommended to use special glasses.
3. Before work, you should make sure the strength of fixing the pink and the rest adjacent to it details.
4. Before turning on the electrolovka to the network it is necessary to check the integrity of the electrical cable.
5. The handle of the cutting device must be securely fixed. IN otherwise The tool can slip and inflict injury.

When drinking billets from various materials, you should always take into account the technical capabilities of the tool. Competent use of the jigsaw and compliance with all security rules in the process of its operation will make it possible to cut any detail without any problems.

Every man, being a real owner, should not only have in his arsenal tools for repair, but also to be able to apply them in practice. It will be about one of the modern tools, namely about the electrolovka. Let's figure it out what it is for the device and how to work with it.

Lobzik with electrical drive is designed for cutting various leafy materials. Depending on the destination, the electrolovka is:

• professional;
• semi-professional:
• household.

Differences are B. specifications and functional features of tools.

Before you know how to use the electroller, you need to get acquainted with its device. The tool consists of:

1. Aluminum corps.
2. Electric motor. A powerful device can cut a thicker and strong material.
3. Cover gearbox.
4. Buttons control of pendulum stroke. The pendulum mechanism allows you to make the exact cut of materials with a small density (soft species of trees, plywood, foam).
5. Casing and brackets that ensure the safety of work.
6. Support roller for maintaining a pink.
7. Swing regulator chips.
8. Regulator Number of Pilking Steps, on which the speed of its movement depends.
9. Tilt regulator plate. It allows you to cut on a tree at an angle of 15, 30, 45 and 90 degrees.
10. Laser guide. Allows you to stick to the drawn line for cutting.
11. Fast-pressure cartridge that performs saw functions.
12. The battery, thanks to which some time you can cut the electric bike without connecting to the network.

Choose saws for jigsaw

Saws are bought separately and selected depending on the material of the cutting canvase and on which cut you need: Direct or curly. The packaging indicates the purpose of the saw, from which material they are made, as well as the direction and size of the teeth.

What can be cut by a jigsaw?

• tree, faeer;
• plasterboard;
• metal;
• aluminum;
• styrofoam;
• glass;
• ceramics;
• rubber;
• skin;
• carpets.

This or that type of saw is selected depending on what you need to sprill.

Consider a species of saw for an electric bike and we define that you can do each of them.

Saws are:

1. With a wide web. Designed for cutting the canvas in a straight line. With such a saw, you do not need to make a lot of effort, but only a little correction direction. For a more accurate line of cutting, you need to enable the "Smooth Start" function at which the motor is gradually gaining momentum.
   
   
   
2. Narrow saw. Need for cutting material on the line curve. To cut off with maximum accuracy, take the device with the rotating head. The radius of the head of the head depends on the electrol bias selected model.
   
3. With large teeth. Their destination is to quickly cut, while quality leaves much to be desired.
   
   
   
4. Pilam with small teeth And thin cannol you can cut the most complex figures.
   
   
   

The quality of the jigsaw work depends on the fastening method. Processing thick sheets with high material density, it is necessary to use equipment with a rigid mount.

Work with dull saws can lead to the tool breakdown, Due to the increase in the load on the motor electrolyzka. It will also reduce the quality of the cut.

Additional devices

Lobzik with electrical drive refers to manual tools, however, if necessary, it can be fixed with stubborn timber and parallel stop.

Sometimes you need to spill the part, covered with a layer of paint or varnish, and I really won't want to scratch it. This case provides for plastics shoe or self-adhesive felt.

In addition to the saws, you can install the tool raspian and grinding nozzles. Thanks to the first corners, it is cleaned with the second, the finished product is cleaned.

Some models provide use pendulum mechanismThrough which the sawing process is accelerated. This function is good for the performance of coarse saws, since the quality and accuracy of the cut line is reduced. When working with plastic and metal, the use of a pendulum mechanism is unacceptable.

During operation, a logs is formed a lot of fine dust, which harms the respiratory authorities. You can get rid of it by connecting the construction vacuum cleaner to the nozzle of the device, which will draw all the dust formed during the operation of the electric jig.

If the purchase of two tools do not afford, there will be enough electrolovka to work with a function of blowing Working area.

How to prepare an instrument

Beginners in this case will be useful to learn how to work properly with the jigsaw, but before we will talk about the preparation of the instrument to use:

1. First of all, you need to carefully examine the instruction manual for the electric appliance.
2. Visually assess the appearance of the device for damage: cracks, chips, cable integrity.
3. Pick a saw in accordance with the quality of the material with which to work.
4. Select the appropriate mode. We give examples: to work with soft tree rocks it is necessary to set the maximum speed and apply the pendulum mechanism. If you need to cut a sheet of chipboard, then leave the high speed of the cutting canvas, but the pendulum mechanism here will be superfluous because it will contribute to the appearance of chips.

To avoid injuries, you need to adhere to the safety technique when working with the jigsaw: Put the protective glasses and gloves.

Marking

Application markup is an important detail, because you need to avoid chipping on the front side of the part. Please note that the chipsets are often formed on the side of the sheet, which is located to a working person. Most often it concerns the sheets of chipboard and fiberboard. Based on this, the markup must be applied on the back side, and placing the facial side canopy.

Council. The cutting process can simplify the presence of a laser guide, with which the correct line is withstanding.

For accurate sawing, it is necessary to place without letters, and the saw lead near the markup line. For the convenience of work, the workpiece must be fixed using a vertical clamp or a spray table.

To learn how to properly cut the jigsaw with an electric drive, our advice will help:

1. Stronger - does not mean better. This applies to the pressure force on the device during operation. This dipping style will lead to a tool breakdown. The correct use of the electrolybiz consists in a strong fixation of the device in the hand and direction of the saw in the desired side.
2. When processing thin metal sheets, vibration occurs. To eliminate it, you need to reduce the speed of the saw movement and put the sheet of plywood under metal. When sawing such a material there is a large load on the jigsaw engine, so you should periodically turn off the device so that the motor is cooled.
3. For high-quality and accurate cut, you need to fix the workpiece.
4. To avoid chipping from the bottom or the top, for example, a laminated chipboard, you must select the saw or the right side to rotate the slab. But if there is a need to get cut without chips on both sides, then on top to the chipboard you need to put a small piece of the same plate, and start sawing. Schole will remain on the additional material, and the desired stove will be with a pure propyl.
5. In order not to appear chips, you can resort such tricks: on the markup to glue the tape.
6. Sawing such a fragile material like plastic, we recommend installing a saw with teeth middle size, turn off the pendulum mechanism and set the smallest speed of the saw movement.
7. In the event that it is necessary to cut the part with a closed loop, and it is impossible to start sawing from the edge, then the hole is drilled in a convenient location, the electric jigsaw saw into it and continue to work.
8. For cutting plexiglas or non-ferrous metals, the saw should be treated with machine oil.

We hope that our tips will help you, and in case of additional questions about how to properly use the jigsaw with an electric drive, you can always see the learning video.

As it turned out, the electrolybiz is an indispensable tool with which even a beginner can cope with. And with the right approach and experience, you can not only perform straight cuts, but also cut various curly parts for the decor.

10170

Share.in Facebook Share.in Telegram Share.in Viber Share.in Twitter

7 Electrolovka applications - instructions from DNIPRO-M

Electric jigsaw is widely used to work with sheet materials. It will come in handy in repair, joinery or furniture workshop. With the help of an electric bike, you can cut soft wood, plastic, Plasterboard, as well as such complex materials as ceramic tile and metal. Depending on the hardness and fragility of the material, as well as the type of propyl, which you want to get, the technique of working with will have some features. In this article we will talk about how to cut the most popular building materials.

What is the electroll bison

Most often, electric jigsaw is used for the manufacture of wood products. Wide application has found this tool in furniture production, where items and details of different shapes make it.

If when working with an electric logger correctly choose the consumage and sawing mode, then you can:

• do smooth and curvilinear propuls;
• cut the circles without damage to the sheet;
• cut thin metal;
• manufacture of woods from wood with a thickness of up to 10 cm (the model of the electric bissing Dnipro-M le-110r cuts bruks at 11 cm);
• cut plastic;
• saw ceramic and porcelain tile.

At the same time you also need to choose. The step of the teeth, their length, material is taken into account.

Getting started: how to turn on the electrolybiz and start sawing

1. Working with electric jigsaw begins with a visual inspection. Tool and power cable should not have visible damage.
2. Next, the saw blade is installed (it should always be removed before storage).
3. Before starting the work of the electroller, the setting is carried out. First of all, the frequency of the saw movement is selected for the material. If you want to make the edge cut, you need to set the corner of the cut. On the electric jigsaw Dnipro-M to do it easily due to the inclined sole. If the task allows you to turn on pendulum, and the amplitude of the web movements is selected.
4. If necessary, a parallel focus or circular is installed to do the holes in the workpiece.
5. If a lot of dust is formed in the work, connect the vacuum cleaner.

Lobsika main purpose - obtaining an even cut. Make it easier.

First of all make a markup that will serve as a guide when working. If the edge of the blank is smooth and you just need to make it less, use parallel emphasis. It is a T-shaped device that is attached to the sole of the electric jigsaw.

To reduce the wear of the saw, the pendulum turns on. Moving the jigsik need slowly, without jerks. Too rapid movement or jerk will be bad on the cut line, and additional processing will be required (for example, grinding).

Curvilinear cut, like smooth, start with marking. Be sure to connect the vacuum cleaner or turn on the purge to remove the garbage from the markup.

Sawning by the electrolovka of figured products is carried out without pendulum stroke. Used at the same time narrow, which makes it easy to change the direction of movement.

Cut in the workpiece circle - one of the most complex tasks for the beginner. But there is nothing incredible in it, since it is possible to quickly work with an electrolybic.

1. Disconnect the pendulum.
2. Make marking.
3. Drill a hole for the saw blade.
4. Install the zircul focus and proceed to work.

Circle can be made with your own hands. To do this, you will need a flat plate and self-tapping screw. On Bruke reliably fix the electrolybiz. Next, measure the desired segment (equal to the radius of the circle), and the center is screwed into the center, which will serve as the axis of rotation.

Electric jigsaw can serve as an alternative in cases where you need to work with the profile, pipes, sheet metal. It is this material that gives the highest load on the tool and the saws. Be prepared for what you need make breaks And often change consumables.

The maximum metal thickness, with which household and semi-professional jigsaws are capable of working, is 10 mm.

Before sawing the metal, you need to cut the metal pick special saw blades.

A set of pylons for metal Dnipro-M t 118 A is made with solid steel and perfectly suitable for straight cuts. In order to reduce wear and prevent melting working part, Use the pendulum function.

The electric jigsaw was created to work with the tree, and therefore it is not entirely strange that most of the work is carried out precisely with this material. Moreover, with the same success, you can cut:

• solid tree;
• lumber;
• pressed wood.

Depending on the thickness of the material, different canvases are used. And they will differ not only with a length, but frequency and size of teeth. The thinner the material - the smaller and the tight to each other should be the teeth.

To obtain a pure cut on thick wood, milking caps with progressive teeth, which gradually decrease.