Circular with a bee with your own hands. Circular saw do it yourself - reliably, practical, cheap! Circular saw design

17.11.2020

For sawing various sawn timber at home, an excellent tool is a manual disk saw. This power tool can cut the lumber of various sections at any angle. Such a tool perfectly cuts sheets of plywood, organity or chipboard.

However, the technical capabilities of such a tool can be significantly expanded, which is often necessary when performing repair workIf you make a stationary machine from a circular saw with your own hands.

It is easy to perform such a reincarnation, and a machine from a circular saw can anyone who needs it. This requires simply consolidate it on the prepared surface in a certain position. In the simplest version, strong building goats can be used as a place of installation. For long-term use of the machine from a circular saw, it is better to make a durable, welded metal strin.

Wooden Circular Saw Machine

To make such a wooden base, you will need:

plywood leaf 8-10 mm thick;
wooden bars with a size of 40x50 mm;
universal glue;
self-tapping screws and bolts with M8 nuts.

A leaf is cut from plywood about 100x60 cm in size (maybe another). At the edges of the sheet of plywood (along its perimeter), bars are attached with glue and self-tapping screws. Then the body of the tool is applied on the inside of the sheet, and the places of its attachment to it are scheduled, as well as the groove for the cutting disk. After that, the electric lobby (can be a mill) was cut into the disk passage, and the holes for fastening the housing are drilled. The legs are attached to the side bars with bolts. The height of the circular saw of the circular saw is selected from 80 to 90 cm. At the pre-prepared place from its inside, the housing is mounted. The bolts for its fastening must be performed in the following (do not perform on the surface). The lid must be covered with varnish or paint.

In order for the material to be squeezed strictly in size, a guide bar is installed parallel to the cutting disc. The bar can be mounted on the surface of the table with clamps. A wooden machine from a circular saw is ready to work.

Back to the category

Metal Stanted Production: Instruction

The machine from the circular saw made of metal is much tougher and stronger than wooden, has a longer service life. To make such a bed, you will need the following material and tool:

metal sheet (preferably steel) is approximately 1000x500 mm and thick from 3 to 5 mm;
metal corner of approximately 45x45 mm;
m8 bolts and nuts;
welding machine;
electric drill;
bulgarian;
clamps.

First of all, the table for the machine from the circular saw is prepared. For this, the metal profile is welded around the perimeter of the metal sheet. So that it fits tightly to the sheet, it needs to be pressed against the surface by clamps. Then, on the back of the sheet, the places of fastening of the housing and the groove for the saw disk are scheduled. The electric drill holes with a diameter of 8 mm for fastening the housing.

With the front side of the hole, the holes are cencing for the installation of fasteners in the tilt.

With the help of a grinder and drills in the table cut the groove for a disk. In order for the groove to cut carefully, you need to drill the holes with a diameter of about 10 mm on the edges of the intended groove and between these holes with a grinder cut the groove. The tool housing is installed and attached to the prepared place.

Four slices are cut from the corner from about 800 to 900 mm long for the table legs. Then the legs are welded to the corners of the table. To give greater rigidity between the legs, a corner is welded at a distance of about 100 mm from the floor surface.

To cut the material to be high quality, you must install the guide bar parallel to the disk. It is best to make it from the corner. To do this, the level corner is cut along the length of the table, then two guides are welded to it, which must record the movement of the plank parallel to the cutting disk. Carnate the bar to the table can be clamps or with a welded plate with bolts.

After the end of the welding works, welding seams are cleaned, the surfaces are degreased and coated with anti-corrosion paint. The machine from the circular saw is ready for operation.

Back to the category

We make a stationary circular

If there is no circular saw, and for work it is necessary to have a more powerful machine, you can make a small stationary machine. Such a machine, made at the factory, is quite expensive, and made with your own hands will be cheaper several times. In order to make such an aggregate, we need the following material and tool:

steel sheet with a thickness of 3 to 5 mm, measuring about 1200x700 mm;
metal corner 50x50 mm;
asynchronous engine at 220 V, 2.2 kW, 2850 rpm. (or another, at the request of the artist);
pulley for the engine;
shaft with bearings and pulley;
wedge belt;
disc saw:
m10 bolts;
welding machine;
bulgarian;
electric drill;
clamps.

First of all, it is necessary to purchase shaft with bearings and mounting for the cutting disk. It can be bought in the building of building materials or order and make in workshops (they often receive ready-made products and cheaper than in the store).

For the size of the prepared sheet from the corner, the frame is boiled. Then it is temporarily installed. After that, there is a marking of the installation of the shaft and the electric motor. Then the frame is breamed two corners with flat surfaces up for fastening the shaft and engine. The prepared frame of the clamps is attached to the sheet and welded. The sheet is cut into the disk groove. In the prepared places, the holes with a diameter of 10 mm for fastening the shaft and the motor. In places of motor mounting in corners, the grooves are cut through holes in the size of the holes (to stretch the wedge belt).

Cut four corners for the machine legs. Prepared legs are welded in the corners of the table frame. The design is cleaned of rust, dirt and painted paint for metal. On the reverse side of the table, the shaft and the engine is mounted bolts, a wedge belt is installed. The belt is stretched by moving the engine along the groove, and then the mounting bolts are tightly tightened. From the end, the engine is mounted on the frame. To ensure a qualitative cut parallel to the disk, a guide bar is installed, which can be mounted on the surface of the table with clamps or bolts in pre-prepared holes. Aggregate is ready to work.

By making the machine from a circular saw, it is possible to significantly ease work on sawing sawn timber.

By building the correctly such an aggregate with your own hands, you can save considerable money.

Every economic man takes care of his home, his condition. During repairs there are many things that can be useful, but it is usually difficult to defier to say how much idea can do. Building a new home or repair it using wood gives a great result. But to get it you must try to try and spend a lot of strength. If you build a house only with the help of a tree, nails and saws with a plane, then the process will be very protracted and heavy, as such a work is so much for one or even several people. To solve such a problem, and invented a circular machine. About him and will be discussed in our current article.

What it is?

The circular machine (with a Fugansky including) is a manual disk saw embedded in the table. Such a part performs many functions and is unique in its kind, since it can cut various figures in contours. If there is a similar device in the house, it will quite simplify the construction of any structure, because this device is more convenient saw, it is more suitable for performing smooth drops and cuts than chainsaw. The material can be processed under any selected angle, this does not represent complexity, compared with the above-mentioned instruments.

The machine can be used to change the form of all materials, which are based on a tree. Its functions can be expanded if you make a circular machine with your own hands at home. But this will be written on. Make a similar tool is not so hard, in some cases you can rely on intuition.

What is needed for manufacture?

To create a machine at home, it is not so much, as it may seem at first glance: just a saw and a table for securing it. These are the most basic components that will continue to perform their role. But you can also add some elements, and it is entirely dependent on the wishes of the owner, creating, for example, the circular machine with the plane itself.

In a simple version, the saw must be attached to the table surface. And the angle in relation to the surface every master chooses himself. This will depend on the convenience of work and the quality of all subsequent products performed using the machine. In order for such an element to serve for a long time, it is necessary to make the right fastening.

Wooden saw

Now let's talk about how to make a wooden circular machine using a saw.

As it was above, the main components are saw and the table for its attachment itself. In addition, we will need:

sheet of plywood or other table coating board;
wooden bars for legs;
universal glue, without it can not be;
self-tapping screws and bolts with nuts.

All of the above items are necessary if there is no finished table and it must be made independently. This option is most practical, as it is necessary to take into account that the machine is not created at no time and not for a year. Therefore, it is better to do everything yourself, check the quality of all parts and fasteners.

Making a circular machine - we make the table

To create the surface of the apparatus, it is necessary to cut a piece of plywood or other material from the sheet, sixty centimeters size. This is the main billet. Brux for legs are attached along the edges, first with glue, and then self-drawing and nuts.

For a future saw, a special hole is cut, which is done using the initial modeling and the discharge of the necessary holes. After that, the jigsik is useful, which is neatly dumped with a hole. This is relatively jewelry, so at this stage it is better not to make mistakes. When working it is necessary to take into account the presence of cutting discs. Without them, the machine will not be able to fulfill its destination.

Now there are places for the bars legs, because the machine must be attached to something. Their length is selected individually, taking into account the growth of the master, although, of course, there are standard sizes, and they range from 80 to 90 centimeters. If it is incorrect to pick up the height, then the master will have to lean much, it will significantly slow down work, since with time it can get a spin.

Exterior finish

At the last stages, when the work on the table for the machine is completed, you must remember appearance Shop furniture. In this case, the bolts do not protrude on the surface: they are not visible, as they are specially hidden and well fixed. The execution of the table at home should not be less qualitative, rather, on the contrary.

Comparison of the first and second stages of work: the manufacture of tables and beds for full equipment

Another important stage, because the quality of the work performed will depend on the productivity of construction or repair, the quality and speed of drinking wood. Previous actions were equally significant only if the desired production product is a machine, and not just a bed for drinking. Further safety depended on the quality of the base, as well as the convenience of performing the work.

If you think about which item can be considered more important in the machine, then it is necessary to consider that the device itself is a one-piece machine that is not subject to separation. In this case, the bed and the base is equally important. As it was above: the basis is responsible for convenience and security, but the bed also takes part of the duties, since very much will depend on the quality of the posting - the entire device will break up at the slightest spark, or this will not happen.

From this we can conclude: making a circular machine with your own hands, it is necessary with the same importance, refer to both stages of the scheme of work on the device, as much depends on them:

the table performs the role of fasteners, it must be high quality and withstand heavy loads, because during work it will have to regularly transfer various gravity, and at the same time it is necessary to maintain the stability of the entire design;
the bed is mounted on a table or basis, from the quality of the execution of this stage of work, the speed of repair and all progress on the cut of the tree will depend on; Also, the safety of wiring should be in the first place.

How to make a metal bed?

The bed, as it was above, was noticed, an important part of the machine, so you have to highlight a lot of time and diligence, in order to achieve due results: extend the service life of the instrument and secure the time of your work. Since the bed will be made of metal, it should be noted that it will require more time and effort than in the case of the basis where it was necessary to check the quality and strength of the wooden table.

What do you need for the manufacture of the bed?

Initial, the most important detail will be the metal sheet (it is desirable that it is steel), the size of 1000 per 500 mm and a thickness of 3 to 5 millimeters. In addition, you will need:

metal corner, approximately 45 to 45 millimeters;
bolts and nuts with thread M8;
welding machine;
bulgarian;
drill;
clamp.

For the manufacture of saws, it is necessary to return to the base, namely to the table. It needs to be strengthened with a metal sheet, it will protect you from many problems while working. All this attachment occurs from the inside, and after it is necessary to cut suitable holes on the surface. The slots make in the form of a puzzle, it will help to accurately work. And what needs to be done for this will be described further.

How to carefully cut a hole on a metal sheet?

Of course, the accuracy does not affect the operation of the machine, but I want everything to be perfect, otherwise there is a feeling of marriage, inferiority, and sometimes disappear to work.

Accuracy will ensure the right start. So that everything went well, it is necessary to circle the contour of the puzzle, the place where the hole is formed. Inside drill a hole in 10 mm, this point is the beginning, from now on, neatly with the help of a special tool begin to cut puzzle over the contour. If the hands are not trembling and everything will be done with marginal care, then work will be released.

In order to provide high-quality mounting of the table, you need to cut four legs, long from 80 to 90 cm. They are tightly welded to the surface. And in order to provide high-quality and strong mount, you must use the same corner at a distance of 10 centimeters from the table surface.

How to make a circular?

If there is no special saw, and for work you need to have a powerful apparatus, you can make a small stationary circular machine for home. Such equipment made at the factory is very expensive. And the machine made with your own hands will cost tens of times cheaper. In order to create such a device, we need the following:

steel sheet with a thickness of 3 to 5 mm, measuring about 1200x700 mm;
metal corner with a cross section of 50x50 millimeters;
asynchronous engine by 220 volts;
motor pulley;
shaft with bearings;
wedge belt;
disk for saws:
m10 threaded bolts;
clamps;
bulgarian;
drill;
welding machine.

How to make a circular machine? First you need to purchase a shaft with bearings and a disk mount. It can be bought at the building materials store or order in specialized workshops (they often receive ready-made products that are cheaper at cost than in the store).

You can now boil the frame from the prepared corner. After that it is installed on the corner. Next, the shaft and an electric motor for the future saw are placed on the circular machine. After that, to continue the manufacture of this part, two corrodes are screwed into the frame, but flat sides up. It is necessary in order to secure the shaft and the saw engine. The prepared frame is attached to the sheet and weld. Next, a hole for a disk is cut into the sheet. At the selected places, holes are drilled up to 10 millimeters for fasteners of the shaft and engine. On this, our homemade circular machine will be fully ready for work. Under the end of the assembly, only stretch a special belt.

Conclusion

Of all the above, you can conclude that it is possible to make a circular machine with your own hands high quality and cheap. And this option is more preferable than buying in the store, as there is the better quality, the more the price of the device. With independent manufacture, you need to pay the same attention to the basis and the cutting tool. Circular machines on wood are able to create real miracles in the hands of the wizard.

Many dacms and owners of private houses faced the need to process and saw boards, plywood and other lumber. For such a work, a circular will be required, which is not difficult to perform from undergraduate funds. Such homemade equipment will not give way to buying in the functionality and quality of execution, allowing you to save several tens of thousand rubles on the acquisition of already ready-made aggregates.

Description of equipment

Circular saws made with their own hands can be stationary or portable. The design of the simplest circular will turn on the metal or wooden carrier frame, inside of which the electromotor is fixed, the electricity supply control unit, the countertop and the working saw itself, which is attached to the circular shaft or installed through the gears and trimmed mechanism. The saw is located in the slots in the worktop, which makes it easy to cut the sawn timber, performing high-quality wood processing.

The table top can be made from sawn timber or use for this ready-made metal blanks. Machine tables are manufactured from wood, from above such a countertop will need to be covered with a durable metal sheet. IN otherwise Without metallic protection, the tree will begin to wear quickly, and equipment for active operation will last for several years, after which it takes a complex and expensive repair.

First of all, it is necessary to determine the main tasks of the sawing machine. If you want to cut boards or firewood for the winter, it is enough to be the simplest installation of a strong table with a slot for a disk.

Separate models involve the presence of an additional shaft to which knives, fugal and plans are attached. Such universal machines are equipped with powerful electric motors, which makes it possible to perform a wide range of wood processing. Machining multifunction machine, you must be guided by high-quality drawings schemes that will allow you to perform universal and reliable equipment.

If various kinds of carpentry work is required, then equip the coordinate table with guides. The available limiters and guides can be fixed at different angles, which makes it possible not only to ensure the safety of work on the machine, but also to perform high-quality wood processing, easily changing discs on saws of different diameters.

Advantages of self-made equipment

Highly popular, homemade circularities use the simplicity of their manufacturer, durability and reliability. Today, many dacms use self-made units, and do not buy expensive equipment in specialized stores.

The main advantages of such equipment include the following:

Universality tool.
Simplicity of its manufacture.
The possibility of substantial savings.
Reliability and durability of equipment.

The schemes of execution of stationary and mobile circulars available on the Internet and thematic prints allow you to make equipment for processing both fine billets and thick sawn timber. You can choose the simplest options that perfectly cope with the processing of lining, thin lamellas and plywood.

Characteristics and power

It is from the correctness of the choice of parameters, including indicators of revolutions and drive power, will depend on the functionality of the use of technology. The maximum permissible diameter of the toothed saw is affected on the power indicator. It is believed that for processing sawn timber with a thickness of about 10 millimeters, an electric motor with a capacity of 1 kW will be required. Based on the thickness of the treated and sawn timber and the power of the electric motor should be selected.

The transmission from the drive in the independently manufactured circular is best to perform a clinorem. This allows you to ensure the necessary safety of the use of technology. Clinoremable transmission when foreign items come under the saw will slip on the pulleys, which eliminates injuries and jamming the working disk.

Circular production

Before you begin directly to the manufacture of a circular machine, it is necessary to think through its device and design, and ideally choose a drawing scheme, which will later be performed by all work. Planning the fabrication of the bed, it is necessary to remember that such a design should be stable and reliable. For production powerful saw, the base is performed from reinforced welded metal structures. For household models, it is possible to use wooden bars for the bed with plywood or weld the base of the metal corner.

The choice of the electromotor used will depend on which works and what wood is planned to be processed on the machine. The drive can operate from single-phase electrical power network or use powerful industrial motors that work from a three-phase electrical network.

Make a powerful and easy-to-use circular car from the motor from washing machine. This will not be much difficult. Such engines have compact dimensions, operate from a single-phase network with a voltage of 220 volts, are distinguished by reliability and are able to operate at high speeds.

One of the most important assemblies electric saws is the shaft on which the working saw is attached. You can use the finished shaft from similar hardware or make it on the molder from the metal of the round. Fill shaft on turning machineBy checking the perfect accurate centering. Even the minimum shaft beating is not allowed, since later it will be impossible to work on such an incorrectly-centered circular machine and unsafe. On the shaft, run the seats under the pulleys and the disk saw.

The saw blade must rise above the surface of the working table with a maximum of a third of its diameter. Otherwise, with a greater height of the saw to handle wood, it will be difficult, and the work on such a machine will be simply dangerous. If you need to work with the bar, the diameter of the saw disk will be approximately 350 millimeters. For processing boards, you should choose small discs, the diameter of which is 250-300 millimeters. The quality of the saws used is necessary to pay due attention, as subsequent to the miniatricular will have a significant load, poor-quality disks are quickly blot and require substitutions.

Materials and tools

Making a circular machine with their own hands will not be a special complexity. For such work, the following materials and tools will be required:

In each case, the circular design will be different, so you need to choose some components, which will make it possible to make a functional and reliable technique. When using lumber for the manufacture of base and desktop, wood will need to be covered with impregnations that protect the material from rotting and exposure to moisture.

Step-by-step assembly

You can make a stationary circular saw from a grinder and a hand cutter without making any changes to the design of the working tool. The base is made of sawn timber, which allows you to significantly simplify the manufacture, eliminating the need to use complex welding equipment. Step-by-step instruction:

This embodiment of the circular saw will be an excellent choice if necessary tool for cutting boards with a thickness of up to 3 centimeters. If you need to make a powerful and multifunctional apparatus for the house, then electric motors with a capacity of 5 kW and more, which allow processing and sawing boards with a thickness of 5-8 centimeters.

The manufacture of a homemade circular saw does not represent a special complexity. You can use grogin or hand sawswhich are mounted inside the wooden base of the machine.

Some masters make a more complex tool that implies the use of powerful electric motors, clinorem and high-diameter saws. If there are any difficulties in the network, you can find thematic videos, telling about how to make a circular with your own hands.

Circular saw is a productive, convenient and maneuverable tool, with which various construction and finishing works are carried out. If you need to perform large volumes of tasks, it is quite difficult to work with manual circular. In such situations, an excellent assistant becomes a table for a circular saw. It can be collected independently of boards and plywood. The saw itself will be placed at the bottom of the table top, and the toothed disk will be held in the slots. The saw turns on, the disk starts to rotate, the sawn timber is supplied and its sawing occurs. If you wish, you can collect a great table for circular saws with your own hands. There is nothing difficult in this work.

It is difficult to work with large volumes of wood with a regular circular, so it is better to install it on the table.

Table design for circular saw

Before collecting circular table With your own hands, you need to carefully think through its design. At this stage, your task is reduced, first of all, to the load calculation, which will be displayed in the future. Collecting the table for a saw with your own hands, take into account the power of the unit. So, for industrial high-power tools, it is recommended to use a reinforced steel welded structure. In the case of a home saw in the device, such a powerful design is not necessary. It will be enough to assemble the table for a saw with your own hands from boards and plywood.

When planning to make a table for a saw with your own hands, you need, as already noted, take into account the power of the tool. In the home workshops most often used saw up to 800 W. At the same time, it is necessary to take into account the frequency and volumes of the work performed. For example, during the construction of the house there will have to cut a much larger material than with any other conditions. Experts do not advise you to buy saws for a house more powerful than 1200 W. In the case of a domestic workshop, this simply makes no sense.

The higher the power of the circular saw and the higher the volumes of the work performed, the more reliable, the table you create is stronger and more stable. Circular saws of the professional class are mounted on the base from metal products. In some cases, such tables are even fit into the floor, since due to the vibration, the operator can briefly lose control over the saw, which will be sufficient to obtain injury. The creation of this table requires certain skills to work with special tools, welding, etc. Assembling the same wooden table for a home saw is available to almost every person even in the absence of such experience.

Preparation for table assembly

Table assembly scheme.

The easiest option of the table for the circular is the design of sufficiently thick plywood and boards. Plywood in this case will be used for the manufacture of table tops. Directly the table top will be stationary. The tool must be installed under it. Previously in the lid, a slot is created, which will move the saw blade.

Call the table sizes, first of all, with a guideline. You should be comfortable and comfortable to work. The instructions consider the average and most common sizes. You can change them at your discretion. The height of the table is 1-1.15 m. Lenten choose with regard to the nature of future works. If most often you saw long boards, the table cover also needs to be done long enough. With a tabletop length, more than 2 m design is recommended to equip an additional pair of supporting legs. Without them, the table will vibrate strongly.

The thickness of the plywood used for the manufacture of the countertops should be from 5 cm. Plexiglas are suitable for the same purpose, fiberglass. From using the Master chipboard, it is recommended to refrain in view of not enough high strength of the material.

The cover is polished and varnished in several layers. This will ensure the required slip of the processed materials. The best option is to strengthen the metal sheet on the worktop. This will increase the reliability of the surface and will extend the life of the product as a whole.

Materials and tools for work

The table for circular saw requires a mandatory presence of guides, due to which the higher accuracy of the sawing of materials will be ensured. Guides are boiled from a metal corner. Clamps usually use clamps to consolidate to the tabletop. Guides are not recommended to make stationary. It will be more convenient if you can change their position in the future.

Prepare materials for self assembly:

Plywood. If you wish, you can use another material for the table top.
A metal sheet.
Bar 50x50 mm.
Board 50x100 mm.
Clamps in the amount of 2 pcs.
Metal corner for the manufacture of guides.

Pre-collect all the necessary tools:

Hacksaw. If possible, it is better to use the electrolovka instead of it.
Screwdriver.
Electric drill.
Manual milling cutter or machine. In the absence, you can do without them.
Roulette and ruler for measurements.
Corolnic

After the preparation of all tools and materials you can start assembling a homemade table. Some wizards use old dining and kitchen tables for this. But it is not worth counting on a greater durability of such products. It is better to do everything yourself, "from scratch." So you can assemble a comfortable table, fully appropriate to your needs and requests.

Step-by-step table assembly instructions

Table of circular machine from steel plate.

First you need to form a worktop. Take a plywood sheet and mark the markup. The edges of the sheet must coincide with two edges of the lid. Drink the workpiece with a hack or electric lobby. If you wish, treat the spike cutter. This is optional, so you can skip this stage. In the case of a table for circular saws, reliability is more important than a beautiful appearance. Perform draft countertops using sandpaper.

At the bottom, prepare a slot for the disk. Measure the sole of the circular saw. To make it possible as convenient as possible, remove the saw blade from the tool and simply circle the desired part of the saw.

After the installation of the landing place is completed, try the stove and make the required adjustments. Seat the slots for the saw disk and fasteners. If the disk should rise and descend, the table must be equipped with a pendulum mechanism. In this case, the shape of the slot must have a type of truncated pyramid. The top of this peculiar pyramid should be sent down. For the manufacture of the frame of the lifting mechanism, it is better to use metal corners cooked with each other.

Build frame and setting legs

Table guide carriage for circular.

Next you need to make marking under the transverse and longitudinal rails. In the case of this table, they perform the rigid rigid function. Make it from the wrong side. Planks are made from Brousa. It is necessary to prepare 2 longitudinal ribs. Lenten pick up the tabletop length. It is enough to take away from it at 8-10 cm on each side. Transverse slats should also be 2. To determine their length, take 8-10 cm from the tabletop width on each side.

Prepare the nests for the self-tapping screw. The rails are fixed in such a way that the lid is about 8-10 cm acted for the edges of the frame. It is important to make the most reliable and durable mount. The first self-tapping screw at a distance of 4-5 cm from the edge of the rail. The self-samples themselves are mounted in a step of 20-22 cm. Details need to be drilled through. Hats of selflessness should be completely recessed in the material of the table top.

Cross ribs are first attached. To ensure maximum reliability of the table, it is necessary to pre-mark the edges of the rails with carpentry glue. Turn the design of the clamps and fix the self-drawing. Leave the table cover until complete drying, after which the same scheme install longitudinal rails. Tighten the frame parts and install several mounts on each side. After that, you can remove clamps.

For the manufacture of legs, use bars. The height of these elements is selected individually in accordance with the growth of the operator. It is more convenient when the countertop is located at the thigh level. Before installing legs, construct them from 1 sides so that the processed side goes to the angle. As a result, the base of the leg will have a slightly large area than the peak.

To fasten the legs, the metal corners are best used. You need to slightly squeeze them in such a way that the base of the improvised table is located. Thanks to this, the bed will become more stable. The mount is performed using bolts with washers. They need to install hats outside. If you install differently, in the process of work, you can be drunk about protruding attachments.

It will make the design even more reliable. Reiki should be installed in pairs from the side of the homemade table.

Carefully polish the surface of the table top and cover it with several layers of varnish. Instead, you can fix with small self-tapping screws a smooth metal sheet.

At the end, the installation of a circular saw to the place intended for it is performed. Additionally, you can apply a markup to the surface of the table top, which will contribute to a more even and proper processing of the sawn material.

Control elements such a machine must be taken out on the outside of the table top. Usually they are fixed on some feet of the table. Performing this stage of work requires some electrical engineering skills. With their absence, it is recommended to contact the appropriate specialist.

Thus, there is nothing complicated in an independent assembly of the table for circular saw. Large temporary and cash costs it does not require. You will spend much less on the materials than on the finished factory, and the quality of the product is not worse than the instruction. Good job!

The circular machine is the tool without which no home master can do. This equipment is especially relevant for a country house or cottage. But it is not always convenient to work with a manual machine, and the factory machines are quite expensive.

The output from the current situation can be the manufacture of this device with your own hands. The basis of this machine may not only be a manual circular saw, but even an electric drill or Bulgarian.

Make a bed for a circular machine with your own hands very simple. For manufacture, the most ordinary pilomber And quite a bit of time.

Before thinking through the design of the upcoming machine, you need to calculate the load that it will be exposed. The main thing in the bed is reliability and stability. For powerful production saws, the base is a welded reinforced metallic design. But for use with your own hands, such an aggregate is not needed.

If you just decided to make your woodworking machine, then you need take into account the main parameters equipment. Since the saws can be different, naturally can be the design of the bed.

First you need determine the power tool. As a rule, equipment is chosen for domestic use, where the power parameters do not exceed 850 watts. But, for example, during the construction of a cottage or country house, it is often necessary to paint very a large number of Woods.

That is, and the power of the circular is required more. But experienced masters do not advise you to buy saws, where this figure is more than 1250 watts. Installing this equipment in the home workshop is absolutely not justified. And the work on it will only increase the cost of electricity.

The larger the machine performance, the stable for it it is necessary. For professional circulars, as a rule, establish the basis, steel profile. Sometimes these birds are even concreted into the floor. Since the vibration of the device can lead to a danger to life.

Technical Features of Circular Machines

Depth of the alleged cut. This parameter depends the thickness of the material to be processed on your machine. This indicator in semi-professional and professional machines ranges in the range of 5-8 cm. For cutting boards and thick plywood, this is quite enough.

But it will be inconvenient to work with the brothers on this machine. In addition, it is necessary to consider that this characteristic of the homemade saw is reduced. The depth of the cut will be less than approximately 1 cm. But this can be avoided if you provide in the table of the table the ability to omit or lift the disk.

In the manufacture of the tool you need take into account the frequency of its rotation. If the circular is required for the workpiece of the building material, then this indicator may be less. If a clean and even cut is required, the rotational frequency is needed quite high. It is necessary, for example, for the manufacture of furniture.

But in this case there are certain nuances. For cutting plastic materials, this saw is not suitable. Due to the very large turns of the tool the disc is heatedAnd plastic begins to melt.

Therefore, it is better to choose a device where the speed of rotation is not more than 4500 rpm, in this case the bed for circular saw can be make from wood. The vibration of this machine is low and the additional strengthening of the table is not required.

Well, at the end that it is necessary to foresee, this is the location of the buttons and other controls on your machine. When assembling saws, do not forget that access the control panel must be safe. Moreover, this is the rule in the case when the open part of the saw is located at the bottom of the table top.

In this design, the panel with switches is best postpone from the outside of the machine Either make a rising countertop. This design is convenient for maintenance of the device. Then, when you took into account all the nuances and trifles, you can start directly assembling the table.

Making a circular saw with your own hands

The easiest option of the beds for the circular is a design made from boards and thick plywood. And directly the tool is attached to the bottom of the stationary countertop. For a saw in the table lid, a special slot is made.

Dimensions for the table can be changed as it will be convenient for it to work on it. For example, the middle table is described, the height of which is 110-120 cm. But there is a lot of depends on the growth of a person working with equipment. Also, at your request, you can change the length of the tabletop.

If it is supposed to work with boards, in which the length is more than 2.6 m, then the lid on the bed will need more. In this case, it is necessary to make changes directly to the design and additionally. add a few supports (legs). Otherwise, the table will create strong vibrations.

For countertops usually used plywoodwhich has a thickness of at least 5 cm. But you can also choose a plexiglass or stove of fiberglass. But the use of chipboard professionals are not recommended, this material is not reliable enough.

Tools and materials for assembly

For circular saw, you must provide for the guides. They help to cut wood much more accurately. This design weld from steel corner And fixed to the lid of clamps.

Fasten the same stationary guides is undesirable, since later you will not be able to change their position.

For the construction of the table you will be needed such materials:

iron sheet;
plywood sheet;
bar size 50 × 50 mm;
50 × 100 mm size board;
steel corner for guides;
two clamps;
manual circular saw.

You also need to pre-cook all the tools that will be necessary for the background assembly:

Sculpture, electric drill.
Hacksaw or electric jigsaw.
Measurement tools (roulette, square, ruler).
Manual milling cutter or milling machine.

When everything is prepared, you can begin the assembly of the table itself. Sometimes masters collect countertops from unnecessary dining or kitchen tables. But this design is unlikely to serve for a long time. Therefore, much more intelligently all elements of the design make with your own hands. In this case, you can also take into account your personal needs.

Making countertops for circular machine

Assembly of the table start from the manufacture of table tops. The plywood sheet is placed so that two edges of the lids are in size with the edges of the iron sheet. Phaneur is cut with a hacksaw or an electric bike.

The edge of the spike can be treated with a cutter, but this operation is optional. Since in the face the main parameter is reliability, and not an attractive view. The countertop rubbing "Naturally" sandpaper.

From the bottom of the countertops noted circular circle. For which at first it is necessary to measure the size of the soles of the aggregate. It is easiest to do this if you unscrew the disk from the device and simply bore the desired part of the saw. These measurements are required to determine the seating.

With the help of a manual cutter, the bars are chosen to a depth of approximately 0.9-1.1 cm. If you do not have a cutter, then this work can be done using a chisel, but this will take it much more.

Then, when the seat is done, try the saw, and if necessary, adjust the recess. Follow the spaces of the slot for the circle and fixing fasteners. If you need a circle to raise and lowered, then it is necessary install pendulum mechanism For countertops.

In this case, the slot must be made in the form of a truncated pyramid. In this case, the hypothetical peak of the pyramid will be directed down. Directly frame for the lifting mechanism is best make from steel cornerswho are welded with each other.

Making frame frame

Markup for fixing transverse speakers and longitudinal, which perform the function of rigidity, it is best to install from the wrong side of the table top. Directly the planks are made from the bar. You will be needed:

Two transverse parts, a long equal tabletop width minus 7-9 cm on each side.
Two longitudinal ribs, the size of equal length of the lid minus 7-9 cm on each side.

Then need make nest for screws. The rails need to be fixed on the lid so that the countertop goes beyond the edges of the frame by 7-9 cm. Fasteners should be as reliable as possible and durable.

The first mount must be set by approximately 40-50 mm from the edge of the rail. Distance between self-sustaining approximately 23-25 \u200b\u200bcm. All items you need to drill through. Saws is attached from the side of the lid so that its hat is completely accumulated in the tree.

Initially fasten the transverse ribs. So that the table lid was as strong as possible, the edges of the rails are predefined wash in joinery glue. The design is fixed by clamps, and without removing them, screws the screws.

The countertop is allowed to dry. After, the longitudinal rails are installed in the same way. Then parts of the frame are tightened with each other by installing two fasteners on each side. Now clamps can be removed.

Fastening legs (supports)

The stands of the table are made of bar. The height of the support is selected individually. In practice, it is more convenient to work at the machine when the countertop located at the hinder level. Before mounting each support, you need to compatinate it so that the leg came down from below. So, the base of the support should be slightly larger, unlike the top area.

It is best to fix legs with steel corners. They need to squeeze a bit so that the base of the machine is in the "strut." It gives the table additional resistance. As a fastener, bolts with washers are used, they are attached to the hats outside. Otherwise, during work, you can be injured about the protruding pieces of fasteners.

The whole design will be stable if additional supports are pulled by diagonal slats. They are fixed in pairs from each side of the machine.

Surface cover polished and treated with varnish Or used to cover a steel sheet, which is attached to the screws. At the very end, to the prepared place, the instrument is fixed directly.

On the cover of the table can be additionally make markingShe will help smoothly and properly saw wood. The circular saw control panel is located on the outer side of the machine. As a rule, it is fixed on one of the legs of the table. That's all, circular saw with their own hands ready.

Views

Save to classmates Save Vkontakte